Dormakaba ED250 Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 60

background image

5

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 3

3.1 Safety instructions

This document contains important instructions for
installation of the ED250 in ground automatic swing
door operator.
Review these instructions thoroughly prior to
installation, and follow them carefully during installation,
commissioning, troubleshooting and maintenance

.

3.2 Door signage requirements

Proper signs and labels shall be applied and maintained on
the door controlled by the ED250 in-ground automatic
swing door operator as referenced in:
• ANSI/BHMA A156.10: Standard for power operated

doors. Ref. Chapter 16.

• ANSI/BHMA A156.19: Standard for power assist and

low energy power operated doors. Ref. Chapter 16.

• Reference Chapter 7, Door signage.

3.3 Safety warnings

WARNING

Damage to equipment or incorrect equipment
operation may result from an incorrec

t

installation.

WARNING

Hazard to mechanical processes by use of
control settings, elements, or procedures not
documented in this manual!

WARNING

Electric shock hazard!
By use of control elements, settings, or
procedures not documented in this manual!

WARNING

Work on electrical equipment and 115 Vac
wiring installation must be performed only by
qualified personnel

!

WARNING

Metallic doors must be grounded per national
and local codes!

3 Safety information

WARNING

Hand pinch point and crushing hazards at door
closing edges!

WARNING

Crushing hazards at door closing edges!

Fig. 3.1

Door closing edges

Opposing

closing edge

Main

closing edge

Secondary

closing edge

3.4 Residual hazards

WARNING

After installation, hazards such as minor
crushing, impact with limited force, and risk to
unsupervised children may exist depending on
structural design of door area, type of door,
and any safeguards that have been
implemented.

«
...
3
4
5
6
7
...
»

Содержание ED250





























































Отзывы:

Нет отзывов

Похожие инструкции для ED250

Бренд: Elettro Страницы: 32

Бренд: Westweld Страницы: 82

MAGNUM TIG THF 238 PRO

Бренд: Spaw Страницы: 10

Бренд: Miller Страницы: 56

Invertec V305-T AC

Бренд: Lincoln Electric Страницы: 2

DYNAMIC HEAT CONTROL PLUS Series

Бренд: Napoleon Страницы: 72

Бренд: Saf-Fro Страницы: 165

Бренд: Century Страницы: 44

Бренд: Century Страницы: 56

Classic Mailbox 42002

Бренд: Simplay3 Страницы: 2

Бренд: SEA Страницы: 2

Бренд: Clarke Страницы: 12

Бренд: Clarke Страницы: 32

Бренд: Bort Страницы: 30

OUTDOOR HEATING AND COOLING UNIT 379H

Бренд: Bryant Страницы: 6

Бренд: Bryant Страницы: 44

Бренд: GILGEN Страницы: 78

Бренд: Unimig Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды