Dormakaba ED250 Скачать руководство пользователя страница 12

Страница: 12 / 60

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 7

Signage and warnings are specified in ANSI /BHMA
A156.10, American National Standard for power
operated pedestrian doors, paragraph 11.

7.1.2 Door, one way traffic

DD0739-020

7.1.1 Overview

7 ED250 door signage

Fig. 7.1.1 One decal, approach, non-approach

1. Arrow and AUTOMATIC DOOR, one side of decal.
• Shall be visible from approach side of a swinging door,

mounted on door at a height of 50" ± 12" from floor to
centerline of sign.

2. DO NOT ENTER and AUTOMATIC DOOR, one side of

decal (or separate decal for solid doors).

• Shall be visible from non-approach side of door that

swings towards pedestrians attempting to travel in
wrong direction.

7.1 Full energy configuration

Fig. 7.1.2 Separate decals, approach, non-approach

7.1.3 Door, two way traffic

1. Arrow and AUTOMATIC DOOR decal.
• Shall be visible from approach side of a swinging door,

mounted on door at a height of 50" ± 12" from floor to
centerline of sign.

2. "CAUTION AUTOMATIC DOOR" decal.
• Swinging doors serving both egress and ingress shall

have a "CAUTION AUTOMATIC DOOR" sign visible
from swing (non-approach) side of door.

• Sign shall be mounted on door at a height of 50 ± 12"

from floor to center line of sign.

Fig. 7.1.3 ACTIVATE SWITCH TO OPERATE decal,

knowing act device

7.1.4 Knowing act door

1. ACTIVATE SWITCH TO OPERATE decal.
• Knowing act doors shall have signage which says

"ACTIVATE SWITCH TO OPERATE" on side of door
having knowing act switch or other knowing act device.

1. AUTOMATIC CAUTION DOOR decal.
• All low energy doors shall be marked with signage

visible from both side of door with the words
"AUTOMATIC CAUTION DOOR".

• Signs shall be mounted 50"

12" from floor to

centerline of sign.

Fig. 7.2.1 AUTOMATIC CAUTION DOOR decal

Fig. 7.2.2 ACTIVATE SWITCH TO OPERATE decal,

knowing act device

7.2.4 Push/Pull used to initiate door operation

Fig. 7.2.3 PUSH TO OPERATE, PULL TO OPERATE decals

1. PUSH TO OPERATE, PULL TO OPERATE decals.
• When push/pull is used to initiate operation of door

operator, doors shall be provided with the message
"PUSH TO OPERATE" on push side of door and
"PULL TO OPERATE" on pull side of door.

7.2 Low energy configuration

7.2.1 Overview

Signage and warnings are specified in ANSI /BHMA
A156.19, American National Standard for power assist
and low energy power operated doors.

7.2.2 All low energy doors

7.2.3 Knowing act switch used to initiate door

operation

1. ACTIVATE SWITCH TO OPERATE decal.
• When a knowing act device is used to initiate operation

of door operator, door shall be provided with sign on
each side of door where switch is operated with
message "ACTIVATE SWITCH TO OPERATE".

Содержание ED250





























































Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды

Dormakaba ED250, Руководство по обслуживанию

Результаты поиска

Содержание ED250

Отзывы:

Похожие инструкции для ED250

Бренды по названию

Популярные бренды