background image

57

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 21

1

1

2

5

5

9

8

21.2  Cement case spindle height adjustment

Fig. 21.2.2  Threaded post adjustment holes, 

5/16" x 5 1/2" cap screws

3

3

1

1

2

6

5

5

7

8

Fig. 21.2.3  Set screw removal 

1

  Cover access hole; 

set screw

2

  Top gearbox plate 

access hole; set 
screw

3

  Access hole set 

screw

5

  5/16" x 5 1/2" cap 

screw

6

  Adjustable plate

7

  Cement case cover

8

 Spindle

21.2.1  Spindle height adjustment.

Spindle bearing is mounted to adjustable 
plate (6).
Two 5/16" x 5 1/2: cap screws (

5

) secure the 

adjustable plate and spindle height in 
position.
Spindle height adjustment is accomplished 
by turning three 5/16" x 2" set screws (

4

)

clockwise to raise the adjustable plate and 
counter clockwise to lower the adjustable 
plate.

21.2.2  Access holes for set screws.

1.  Gearbox cover contains access holes 

(1

)

for two set screws (Fig. 21.2.2).

2.  Top gearbox plate (9) contains access 

hole (

2

) for one set screw (Fig. 21.2.2).

21.2.3  Adjusting spindle height.

1.  Remove two set screws (

3

) from gearbox 

cover access holes (1) using  
5/32" T-handle hex key (Fig. 21.2.3). 

2.  Slightly loosen two 5/16" x 5 1/2" cap 

screws (

5

) using 9/16" socket.

3.  Rotate the three cup point set screws (

4

(Fig. 21.2.1) clockwise to raise spindle 
height and counter clockwise to lower 
height. Use 5/32" T-handle hex key.

•  Turn each set screw an equal amount 

when adjusting spindle height.

21.2.4  Spindle height adjustment 

completed.

1.  Tighten two 5/16" x 5 1/2" cap screws (

5

using 9/16" socket (Fig. 21.2.3).

2.  Reinstall two set screws (

3

) in cover access 

holes (Fig. 21.2.3).

Fig. 21.2.1  Height adjustment set screws

4

  5/16" x 2" cup point 

set screw

5

  5/16" x 5 1/2" cap 

screw

6

  Adjustable plate

8

 Spindle

4

4

6

8

5 5

1

  Gearbox cover 

access hole for set 
screw

2

  Top gearbox plate 

access hole for set 
screw

5

  5/16" x 5 1/2" cap 

screw

6

  Adjustable plate

7

  Cement case cover

8

 Spindle

9

  Top gearbox plate

Содержание ED250





























































Отзывы: