background image

 

12  

 

 

 

BASIC TROUBLESHOOTING GUIDE 

PROBLEM 1: THE UNIT HAS NO POWER 
1.  Check if the unit is switched ON. 
2.  Check the fuse. Replace with the same type if fuse is blown. 
3.  Check the power cord and ensure there are no disconnections. 
4.  Verify that the unit is properly connected to the power source. 
 
PROBLEM 2: PANEL DISPLAYS “Err” MESSAGES 
DESCRIPTION: 
Display show “SEnS” “Err” messages. \ 
 
ERR0  — First external temperature probe not detected
 
ERR1  — Second external temperature probe not detected 
ERR2  — Internal  temperature probe not detected 
ERR3  — First external temperature probe not  attached. 
 
SOLUTION: 
Turn off power and back on.  
If err messages shows err0 or err1 check the connection of sensor to 
its receptacle. Check if the temperature probe tip is still intact. 
 
If err messages shows err2 internal temperature connector might have 
come loose or needs to be replaced. 
 
If err messages shows err3, the first external temperature probe was 
not detected, secure the external temperature on the underside of the 
board to be worked on. 
 
PROBLEM 3: DISPLAY AND OTHER DEVICE OPERATION 
ISSUES 
SOLUTION: 
Turn off power and back on.  
 
OTHER PROBLEMS NOT MENTIONED: 
Contact the vendor. 

 

IR-Preheating System

 

Int883

 

INSTRUCTION MANUAL

 

Thank you for purchasing Aoyue Int 883 IR-Preheating System. 

It is important to read the manual before using the equipment. 

Please keep manual in accessible place for future reference. 

This  manual  is  designed  to  familiarize the technician with 

the proper operation and maintenance of the equipment. 
The “Care and Safety Precautions” section explains the 

hazards of using any type of soldering or reworking device. 

Please read carefully and observe the guidelines in order to 
maximize usage and minimize the risk of injury or accidents . 

Содержание Int883







Отзывы: