Doran GuardianXL Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 87

background image

4

Chapter 1

Introduction

Thank you for purchasing this DORAN SCALE product. The

GuardianXL

Weighing

System is designed to provide consistent reliability in the most demanding environments.
The

GuardianXL

Indicator is designed and manufactured in DORAN SCALE’s corporate

headquarters in Batavia, Illinois. DORAN SCALE’s ISO9000 certification assures that
your

GuardianXL

Indicator is manufactured to deliver the highest quality product

possible.

This manual describes the installation, operation and functionality of the

GuardianXL

Intrinsically Safe Indicator. Please be sure to read the entire manual to leverage the
multitude of benefits that the

GuardianXL

provides. If any questions arise, please feel

free to contact your local DORAN SCALE distributor or the DORAN SCALE Technical
Support Department at 1-800-262-6844.

Unpacking the

GuardianXL

Before unpacking your Doran product, please read the instructions in this section. Your
new

GuardianXL

is a durable industrial product, but it is also a sensitive instrument.

Normal care should be taken when handling and using this product. Improper handling
or abuse can damage the unit and result in costly repairs that will not be covered by the
warranty. If you notice any shipping damage, notify the shipper immediately. Please
observe the following precautions to insure years of trouble free service from your new
product.

¾

DO NOT drop the enclosure.

¾

DO NOT immerse the enclosure.

¾

DO NOT drop objects on the enclosure.

¾

DO NOT pick up the enclosure by the cables.

¾

Carefully remove the enclosure from the shipping carton

«
...
3
4
5
6
7
...
»

Содержание GuardianXL
























































































Отзывы:

Нет отзывов

Похожие инструкции для GuardianXL

Бренд: Davis Instruments Страницы: 16

Бренд: Canon Страницы: 14

IMAGE STABILIZER EF70-200MM F/4L IS USM

Бренд: Canon Страницы: 13

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 3

TIMER REMOTE CONTROLLER TC-80N3

Бренд: Canon Страницы: 2

EF-S55-250mm f/4-5.6 IS II

Бренд: Canon Страницы: 7

Бренд: 1byone Страницы: 9

Бренд: hager Страницы: 4

Formula F732 WIZARD

Бренд: Datalogic Страницы: 2

MARTEN-FREE CAR

Бренд: Gardigo Страницы: 36

Бренд: WÄRTSILÄ Страницы: 64

Бренд: VARIZOOM Страницы: 5

Бренд: VARIZOOM Страницы: 5

Бренд: NavLinkz Страницы: 4

Бренд: AirTest Страницы: 4

Бренд: Flymo Страницы: 24

Бренд: Kingpin Страницы: 4

Бренд: Miller Страницы: 18

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды