Doosan DV11 страница 106 Скачать руководство пользователя

Страница: 106 / 220

DV11

Operation and Maintenance

103

Engine Reassembly

Printed in Mar. 2005 PS-MMA0608-E1A

2) Clean the holes which an injector and a high pressure connector will be put into

before they are assembled. Engine oil and fuel that might went into during

disassembly should be wiped out especially for the holes where a fuel high

pressure connector & an injector will be put into.

3) Coat the fresh engine oil on the O-ring of the injector. At the same time, be

careful not to allow the engine oil or foreign material to go into the holes for a fuel

high pressure connector.

4) First, set the position between the hole of fixing bracket and the tap hole of the

bolt for injector fixing bracket. Second, insert the injector vertically to the hole.

Put the bolt of the injector fixing bracket into a thread on the head and tighten

about 2 ~ 3 turns with hands.

5) Temporarily mount the fixing bolt assemble with pre-tightening torque while

aligning an injector and a fuel high pressure connector. Through this step, the

sealing and O-ring is placed correctly on the cylinder head and fuel lines are to

be fit together.

Afterwards release the injector by loosening the fixing bolt

and then injector pre-load leads to 0 (zero) kg.m

6) Coat the fresh and clean engine oil on O-ring, Hold down shoulder and

Thread of fixing nut. Grasp high pressure connector with balls vertical and insert

it into the hole on while aligning the balls of connector and slot of the head. Push

the connector into the hole until feeling it contacted.

Injector fixing bracket bolt

Fuel high pressure

connector fixing nut

Temporarily

torque

0.3 kg.m

1.5+0.5 kg.m

1,2

step : Installing injector & pre-tightening

step : Installing high pressure connector

& temporarily assembling

Install the injector with pre-tightening
torque and then loosen the fixing bolt.

Mount the high pressure
connector and then
assemble the fixing nut with
pre-tightening torque.

1,2

Assemble the seal ring for
the contacted surface it.

Downloaded from

www.Manualslib.com

manuals search engine

Содержание DV11





























































































































































































































Результаты поиска

Содержание DV11

Отзывы:

Похожие инструкции для DV11

Бренды по названию

Популярные бренды

Doosan DV11, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DV11

Отзывы:

Похожие инструкции для DV11

Бренды по названию

Популярные бренды