manualshive.com logo in svg

Doosan DV11, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan DV11 Скачать руководство пользователя страница 34

 

DV11 

  Operation and Maintenance

 

 

31

Technical Information

Printed in Mar. 2005    PS-MMA0608-E1A

 
2.3.20. Turbo charger 

z

 The turbocharger needs not any 

specific maintenance. 

z

  Every time of engine replacement, a 

leakage or clogging of oil pipes 
should be inspected. 

z

  Air cleaner should be maintained 

carefully for nut or foreign material 
not to get in. Periodic inspection 
should be applied on the 
compressed air and exhaust gas 
pipes, For leaking air will bring the 
overheat engine, an immediate 
repair must be done. 

z

  During the operation that is surrounded by the dust and oil mixed air, frequent 

cleaning must be done on the impellers. Tear down the impeller casing (attention: 
be careful not to bend) and must clean with non-acid solvent solution. If necessary, 
use plastic scraper If impeller is severely polluted, dip the impeller into solution 
and may be better to clean it with stiff brush 

Then one thing to beware is to dip only impeller part and so do not support by 

impeller but bearing housing. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Содержание DV11





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды