manualshive.com logo in svg

Doosan DV11, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan DV11 Скачать руководство пользователя страница 37

 

DV11 

  Operation and Maintenance

 

 

34

Technical Information

Printed in Mar. 2005    PS-MMA0608-E1A

 

z

  The density of anti-freezing solution and additive for rust prevention is able to be 

confirmed by the cooling water test kit. 
(

Fleetguard CC2602M

 or 

DOOSAN 60.99901-0038

) 

 

z

  How to use the cooling water test kit 

(1) When the cooling water temp. of engine is in the range of 10   55 

～

°

C, loosen 

the plug for cooling water discharge and fill the plastic cup about a half. 

 

NOTE: 
In taking the cooling water sample, if the water in auxiliary tank were taken, it 
is hard to measure the accurate density. Take the cooling water sample 
necessarily loosening the cooling water discharge plug. 
 

(2) At the state of a test paper soaked in the sampled water, after 3 - 5 seconds 

past, take the paper out through water agitation, and shake off the water. 

(3) Wait for about 45 sec. till the color change of test paper. 
 

 

NOTE: 
However, it should not elapse longer than 75 sec, and if it did, the hue would 
change. 

 

(4) Make the numerical value by comparing the test paper which hue has 

changed with the color list of label on storage bottle. 

(5) By comparing the hue changed into yellowish green or so with the green color 

indication of test paper storage bottle, confirm the density. (Then, the density 
indication must be in the hue range of 33% to 50%). 

(6) The brown at the middle of test paper and the lower pink color indication 

represent the additive state for rust prevention, and the proper range is that 
the meeting numerical value of brown (vertical) and pink color (horizontal) 
locates in the range of 0.3 to 0.8 at the color list of label on the test paper 
storage bottle. 

(7) In case of less than 0.3, replenish the additive for rust prevention (DCA4), and 

in case of more than 0.8, pour out the cooling water about 50% and then 
readjust the density after refilling with clean fresh water. 

 
 

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Содержание DV11





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды