manualshive.com logo in svg

Doosan DV11, Руководство по эксплуатации и обслуживанию

Поделиться
Скачать
Doosan DV11 Скачать руководство пользователя страница 185

 

DV11 

  Operation and Maintenance

 

 

180

Maintenance of Major Components

Printed in Mar. 2005    PS-MMA0608-E1A

 

5. Maintenance of Major Components 

 

5.1. Cooling System 

5.1.1. General descriptions and main data 

z

  This engine is water-cooling type. Heat from the combustion chamber and engine 

oil heat are cooled down by coolant and radiated to the outside, resulting in the 
normal operation of the engine. 

z

 Looking into the cooling system, the water pumped up by the water pump 

circulates around the oil cooler through the water pipe to absorb the oil heat, and 
then flows through the water jacket of the cylinder block and water passage of the 
cylinder head to absorb the heat of the combustion chamber. 

 

z

 

The water absorbing the oil heat and combustion chamber heat goes on to the 
thermostat through the water pipe, and circulates to the water pump if water 
temperature is lower than the valve opening temperature on the thermostat, while 
circulating to the radiator at water temperature higher than the valve opening 
temperature. At the radiator, the heat absorbed in the coolant is radiated to cool 
down and the coolant recirculates to the water pump.

 
 
 
 

 

Radiator 

Cylinder block

Water pump 

Thermostat

Oil cooler 

Cylinder block 

Cylinder head 

Cylinder no.

Downloaded from 

www.Manualslib.com

 

manuals search engine

 

Содержание DV11





























































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды