Doosan DV11 страница 4 Скачать руководство пользователя | Manualshive

Страница: 4 / 220

background image

DV11

Operation and Maintenance

1

Safety regulations & specifications

Printed in Mar. 2005 PS-MMA0608-E1A

1. Safety Regulations & Specifications

1.1. Safety Regulations

1.1.1. General notes

z

Day-to-day use of power engines and the service products necessary for running

them presents no problems if the persons occupied with their operation,
maintenance and care are given suitable training and think as they work.

z

This summary is a compilation of the most important regulations, These are

broken down into main sections which contain the information necessary for
preventing injury to persons, damage to property and pollution. In addition to
these regulations those dictated by the type of engine and its site are to be
observed also.

IMPORTANT:

If despite all precautions, an accident occurs, in particular through contact

with caustic acids, fuel penetrating the skin, scalding from oil, antifreeze being

splashed in the eyes etc, consult a doctor immediately.

1.1.2. To prevent accidents with injury to persons

(1) Engine starting and operation

z

Before putting the engine into operation for the first time, read the operating

instructions carefully and familiarize yourself with the “critical” points. If you
are unsure, ask your DOOSAN representative or service man.

z

For reason of safety we recommend you attach a notice to the door of the

engine room prohibiting the access of unauthorized persons and that you
draw the attention of the operating personal to the fact that they are
responsible for the safety of person who enter the engine room.

z

The engine must be started and operated only by authorized personnel.

z

Ensure that the engine cannot be started by unauthorized person.

z

When the engine is running, do not get too close to the rotating parts.

z

Do not touch the engine with bare hands when it is warm from operation risk

of bums.

z

Exhaust gases are toxic. If it is necessary to run an engine in an enclosed

area, remove the exhaust gases from the area with an exhaust pipe
extension.

Downloaded from

www.Manualslib.com

manuals search engine

«
...
2
3
4
5
6
...
»

Содержание DV11





























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для DV11

Бренд: KCFA Страницы: 2

Бренд: GAPOSA Страницы: 20

Бренд: Amico Страницы: 47

Бренд: Saito Страницы: 27

Бренд: Hyundai Seasall Страницы: 150

Бренд: Volvo Penta Страницы: 44

Бренд: Volvo Penta Страницы: 90

Бренд: Hino Motors Страницы: 339

Бренд: YS Страницы: 2

Бренд: Greyhound Страницы: 20

Бренд: Honda Страницы: 46

Бренд: O.S. engine Страницы: 2

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMH-5830-490

Бренд: O.S. engine Страницы: 2

O.S.MOTOR OMA-2820-950

Бренд: O.S. engine Страницы: 2

MAX-46FX-Hring Series

Бренд: O.S. engine Страницы: 30

Бренд: O.S. engine Страницы: 29

Бренд: O.S. engine Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды