Doosan DV11 Скачать руководство пользователя

Страница: 164 / 220

DV11

Operation and Maintenance

159

Engine Diagnostic

Printed in Mar. 2005 PS-MMA0608-E1A

3.8.4. Engine brake control

Engine brake is worked by the operation of the engine brake switch in the

dashboard.

- Engine brake : There is section of one shift and two shift.

One step : the function of the braking is operated at the three cylinders

only.

Two step : the function of the braking is operated at the six cylinders all.

Operating method

Engine brake switch : [first step] , [second step] , [OFF]

Operating condition

- Engine brake switch : normal
- Vehicle speed

: more than specified speed.

- Engine speed

: more than specified speed.

- Oil temperature

: more than specified temperature.

Free condition

- Engine speed

: less than specified speed.

- Vehicle speed

: less than specified speed.

- Accelerator pedal

: depressed or pedal trouble.

- Clutch pedal

: depressed or pedal trouble.

- Oil temperature

: less than specified value.

3.8.5. Cruise control

Provide the driver with ability to control in order to travel and maintain a setting

speed.

Operation switch : [SET/INC], [SET/DEC] , [RESUME] , [CRUISE OFF]

Operating method

- Range of vehicle speed of possible cruise control : 40 - 100 km/h
- Cruise control is standard by when the vehicle speed is more than 40km/h,

cruise control is disabled when the vehicle speed is less than 40km/h.

- Setting of the cruise control by using the accelerator pedal.

After the vehicle speed is raised by pressing the accelerator pedal,

pressed switch [SET] at the time of desired vehicle speed.

Switch [SET/INC] or [SET/DEC] have the functions of [SET] all.

- Setting of raise / drop by using the switch during cruise running.

Adjusting for raising of cruise vehicle speed : switch [SET/INC] is pressed.

Adjusting for dropping of cruise vehicle speed : switch [SET/DEC] is

depressed.

Switch [SET/INC], [SET/DEC] is depressed once, is increased as one

step, and is increased continuously when is kept on depressing.

Downloaded from

www.Manualslib.com

manuals search engine

Содержание DV11





























































































































































































































Результаты поиска

Содержание DV11

Отзывы:

Похожие инструкции для DV11

Бренды по названию

Популярные бренды

Doosan DV11, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание DV11

Отзывы:

Похожие инструкции для DV11

Бренды по названию

Популярные бренды