DOMUSA Fusion Hybrid Gas Condens, Инструкция по установке и эксплуатации

Страница: 51 / 76

49
49 49
49
17 17 17 17 COMB COMB COMB COMBUSTION ADJUSTMENT USTION ADJUSTMENT USTION ADJUSTMENT USTION ADJUSTMENT
The module combustion adjustment must be carried out by the Official Technical Assistance Services
of
DOMUSA TEKNIK DOMUSA TEKNIK DOMUSA TEKNIK DOMUSA TEKNIK . Any operation performed on the parameters related to combustion, without
considering this section of the manual, may cause damage to people, the module and the installation.
DOMUSA TEKNI DOMUSA TEKNI DOMUSA TEKNI DOMUSA TEKNIK K K K will hold no liability for any damage caused by unsuitable handling of the power
regulation elements carried out by personnel not authorised by the company.
As described on the plate plate, the module Fusion Hybrid Fusion Hybrid Fusion Hybrid Fusion Hybrid Gas Gas Gas Gas Condens Condens Condens Condens is adjusted by default to run
on Natural Gas. In case of working with another type of gas, it will be necessary to replace the gas
through parameter
P02 P02 P02 P02 of the
"Technical Menu"
before regulating the boiler. (see
"Adapting to other
gases types"
)
.
17.1 17.1 17.1 17.1 Measurement values Measurement values Measurement values Measurement values
When it is started up, check that the O
2
value is within the values indicated in the table below. To
do this, an operating mode is available that sets the minimum (Lo) and maximum (Hi) power of the
boiler for a correct combustion test. (See
"Service Mode"
).
Make sure that Make sure that Make sure that Make sure that the air intake pipe of the the air intake pipe of the the air intake pipe of the the air intake pipe of the module module module module is f is f is f is fully closed and that the sealing is ully closed and that the sealing is ully closed and that the sealing is ully closed and that the sealing is
en en en ensured during sured during sured during sured during calibration. calibration. calibration. calibration.
NATURAL GAS NATURAL GAS NATURAL GAS NATURAL GAS
(G20) 20 mbar
CO
2
(%)
O
2
(%)
Maximum power Maximum power Maximum power Maximum power
P2: Hi P2: Hi P2: Hi P2: Hi
Rated value 9,0 4,8
Tolerance 8,7 – 9,3 5,4 – 4,3
Ignition power Ignition power Ignition power Ignition power
P1
P1 P1
P1
Rated value 9,0 4,9
Tolerance 8,7 – 9,3 5,4 – 4,3
Minim Minim Minim Minimum power um power um power um power
P0: Lo P0: Lo P0: Lo P0: Lo
Rated value 9,1 4,8
Tolerance 8,7 – 9,5 5,5 – 4,2
PROPANE GAS
PROPANE GAS PROPANE GAS PROPANE GAS
(G31) 37 mbar
CO
2
(%)
O
2
(%)
Maximum power
Maximum power Maximum power
Maximum power
P2: H P2: H P2: H P2: Hiiii
Rated value 10,4 5,3
Tolerance 10,0 – 10,5 5,9 – 5
Ignition power Ignition power Ignition power Ignition power
P1
P1 P1
P1
Rated value 10,4 5,2
Tolerance 10,0 – 10,5 5,9 – 5
Minimum power Minimum power Minimum power Minimum power
P0: Lo P0: Lo P0: Lo P0: Lo
Rated value 10,3 5,3
Tolerance 10,0 – 10,5 5,9 – 5
CO CO CO CO values must not exceed in all process 2%. values must not exceed in all process 2%. values must not exceed in all process 2%. values must not exceed in all process 2%.
If, after making the adjustment, the value obtained in the measurement deviates from the established
range, check that the gas evacuation and air intake systems do not leak and or not communicating
with each other.
After verifying that the installation, the gas evacuation system and the gas circuit comply with all
requirements, the O
2
value must be adjusted according to the following instructions: