Ditch Witch SK650 Скачать руководство пользователя страница 70

Страница: 70 / 83

SK650 Operator’s Manual

Service - 69

As Needed

CMW

Jump Start Unit

Incorrect procedures could result in death, injury, or property damage.

Use equipment correctly.

NOTICE:

•

Park on level area.

•

Put all drive controls in neutral and lower all unstowed attachments.

•

Turn off all electrical loads.

•

Turn off engine and remove key from ignition.

•

Block wheels or tracks.

Explosion possible. Serious injury or equipment damage could occur.

Follow directions carefully.

NOTICE:

•

Lead-acid batteries vent explosive hydrogen gas when charging.

•

Do not smoke, create sparks, or use flames around batteries.

•

NEVER lean over battery when making connections.

•

Do not allow vehicles to touch when jump starting.

•

Wear eye protection and remove metal jewelry and watches.

•

Do not attempt to jump start a battery that is leaking, bulging, heavily corroded, frozen, or
otherwise damaged.

•

NEVER short-circuit battery terminals for any reason.

•

NEVER hammer on battery posts or cable terminals.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды