Ditch Witch SK650 Скачать руководство пользователя страница 51

Страница: 51 / 83

Complete the Job - 50

SK650 Operator’s Manual

Rinse Equipment

CMW

Rinse Equipment

Spray water onto equipment to remove dirt and mud.

Open hood and allow unit to cool. Remove debris from inside of unit.

Remove mud from track sprockets.

Wash undercarriage. Pay special attention to brake pins area.

Disconnect Attachment

Lower attachment to the ground.

Turn off engine.

Disengage lock pins by turning handles away from center of attachment.

Cycle attachment drive control and disconnect hydraulic hoses, if used.

Start engine.

Tilt mount plate forward and back unit away from attachment.

Stow Tools

Make sure all tools and accessories are loaded and properly secured on trailer.

NOTICE:

Do not spray water onto operator’s console. Electrical components could be damaged.

Wipe down instead.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды