Ditch Witch SK650 Скачать руководство пользователя страница 57

Страница: 57 / 83

Service - 56

SK650 Operator’s Manual

Startup/10 Hour

CMW

Startup/10 Hour

Check Engine Oil Level

Check engine oil level at dipstick opening (1) at
startup and every 10 hours. Oil level should be at
top of marking. If low, add DEO at fill (2). Check
with unit on level surface and at least 15 minutes
after stopping engine.

Check Engine Air Filter Service
Indicator

Check air filter service indicator (shown) at
startup and every 10 hours and change filter as
needed. See “Change Air Filter” on page 68.

Location

Task

Notes

Traction Unit

Check engine oil level

DEO

Check engine air filter service indicator

Check engine coolant level

DEAC

Grease front track idler rollers

MPG

Check hydraulic fluid level

THF

Check brake operation

Check track tension

Check hydraulic hoses

IMPORTANT:

Use oil specified in “Engine Oil

Temperature Chart” on page 55.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды