Ditch Witch SK650 Скачать руководство пользователя страница 43

Страница: 43 / 83

Transport - 42

SK650 Operator’s Manual

Lift

CMW

Lift

Points

Lifting points are identified by lifting decals. Lifting at other points is unsafe
and can damage machinery.

Procedure

Use a hoist capable of supporting the equipment's size
and weight. See “Specifications” on page 73 or
measure and weigh equipment before lifting.

To lift unit with attachment, use four lift points as shown.

To lift unit without attachment, use one of the methods
below:

•

Use two points nearest operator station.

•

Use four lift points as shown.

Crushing weight. If load falls or moves it could kill or crush you. Use

proper procedures and equipment or stay away.

IMPORTANT:

Front of unit will be lower than

rear of unit when using only two lift points.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды