manualshive.com logo in svg

Ditch Witch SK650, Руководство оператора

Операторский мануал для Ditch Witch SK650 - необходимая документация для правильного использования этого оборудования. Скачайте бесплатно руководство по эксплуатации с нашего сайта manualshive.com, чтобы быть в курсе всех функций и характеристик этого продукта. Удобно и просто!

Поделиться
Скачать
background image

Service - 68

SK650 Operator’s Manual

2000 Hour

CMW

2000 Hour

Change Engine Coolant 

Drain cooling system at drain (2). Add approved 
coolant at fill (1) every two years or 2000 hours.  

As Needed

   

Change Air Filter   

Change air filter when red band on indicator is 
visible. 

1.

Open air filter housing at latches (2).

2.

Remove primary (3) and secondary (4) 
elements.

3.

Wipe inside of housing and wash end cup.

4.

Insert new primary and secondary elements.

5.

Close air filter case.

6.

Reset air filter service indicator (1).

NOTICE: 

•

The use of non-approved coolant may 
lead to engine damage or premature 
engine failure and will void engine 
warranty.

•

See page 55 for list of approved coolants.

Содержание SK650




















































































Отзывы:

Нет отзывов

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Загрузить еще бренды