Ditch Witch SK650 Скачать руководство пользователя страница 27

Страница: 27 / 83

Controls - 26

SK650 Operator’s Manual

Controls

CMW

Attachment drive
control

To engage attachment drive
in reverse, lift lever lock and
push forward.

To engage attachment drive
in forward, lift lever lock and
pull back.

IMPORTANT:

•

Lever lock engages when control
is in neutral.

•

Use foot pedal to hold attachment
control in the on position when
hands are busy operating lift arm
or track drive controls.

Lift arm control

To move lift arms down, push.

To float, push forward to end.

To move lift arms up, pull.

To curl attachment up, move
to left.

To curl attachment down,
move to right.

IMPORTANT:

Exercise caution when

lifting loads. See page 74 for
operating capacities.

Attachment drive foot
control

To hold attachment drive in
forward position, operate
attachment drive control and
press pedal.

To return attachment drive
control to neutral, release
pedal.

IMPORTANT:

Use foot pedal to hold

attachment control in the on position
when hands are busy operating lift
arm or track drive controls.

Item

Description

Notes

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды