Ditch Witch SK650 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 83

Ditch Witch SK650 Скачать руководство пользователя страница 4

SK650 Operator’s Manual

Overview - 3

Intended Use

CMW

Intended Use

The SK650 is a platform, rubber track mini skid steer unit designed for light-to medium-duty construction
work. The SK650 has a quick attach mount plate which makes it easy for an operator to connect different
attachments. The unit is designed for operation in temperatures typically experienced in earth moving and
construction work environments. Provisions may be required to operate in extreme temperatures. Contact
your Ditch Witch dealer.

Use in any other way is considered contrary to the intended use.

The SK650 should be operated, serviced, and repaired only by persons familiar with its particular
characteristics and acquainted with the relevant safety procedures.

Equipment Modification

This equipment was designed and built in accordance with applicable standards and regulations.
Modification of equipment could mean that it will no longer meet regulations and may not function properly
or in accordance with the operating instructions. Modification of equipment should only be made by
competent personnel possessing knowledge of applicable standards, regulations, equipment design
functionality/requirements and any required specialized testing.

«
...
2
3
4
5
6
...
»

Содержание SK650




















































































Отзывы:

Нет отзывов