Ditch Witch SK650 Скачать руководство пользователя страница 44

Страница: 44 / 83

SK650 Operator’s Manual

Transport - 43

Hau

CMW

Hau

Load

Disengage parking brake.

Start engine.

Adjust throttle to low speed.

Pull lift arm control to raise mount plate (and attachment) clear of trailer, but keep it low.

Move unit to rear of trailer and align with ramps.

Move both track drive controls forward and slowly move unit onto trailer until tiedown position is
reached.

Push lift arm control to lower mount plate (and attachment) to trailer bed.

Apply parking brake.

Ensure that all controls are in neutral position.

10. Turn ignition switch to STOP.

11. Tie down unit.

Crushing weight. If load falls or moves it could kill or crush you. Use

proper procedures and equipment or stay away.

NOTICE:

•

Load and unload trailer on level ground.

•

Incorrect loading can cause trailer swaying.

•

Attach trailer to vehicle before loading or unloading.

•

Ten to fifteen percent of total vehicle weight (equipment plus trailer) must be on tongue to help
prevent trailer sway.

NOTICE:

•

If loading onto tilt-bed trailer, be prepared for trailer to tilt.

•

Move all controls to neutral position when stopped.

Содержание SK650




















































































Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды

Ditch Witch SK650, Руководство оператора

Результаты поиска

Содержание SK650

Отзывы:

Похожие инструкции для SK650

Бренды по названию

Популярные бренды