DINSE DIX PI GO 2006.M, Руководство по эксплуатации

Страница: 3 / 36

3
- The SWS “Smart Welding Stop” system at the end of TIG
welding. Lifting up the torch without switching off the arc will
introduce a slope down and it will switch off automatically.
- “Energy Saving” function to operate the power source cool-
ing fan and the torch water cooling only when necessary.
•
High electrical performance resulting in a reduction in ener-
gy consumption.
•
Professional large diameter 4-roller wire feeder that guaran-
tees precise and constant feeding of the wire. This wire feed-
er’s principal characteristics are:
- Designed for use with all types of solid and core type wire.
- A 24 V direct current ratio motor.
- A gas solenoid valve.
- Wire speed (welding current) and welding voltage adjust-
ment.
- Graduated knobs for precise adjustment of the wire pres-
sure that stays unvaried when the arms open and close.
- The feeder rollers can be replaced without using any tools.
Technical data
The general technical data of the system are summarized in
table 1.
Usage limits (IEC 60974-1)
The use of a welding power source is typically discontinuous,
in that it is made up of effective work periods (welding) and rest
periods (for the positioning of parts, the replacement of wire
and underflushing operations etc. This welding power source
is dimensioned to supply a I
2
max nominal current in complete
safety for a period of work of 35% of the total usage time. The
regulations in force establish the total usage time to be 10 min-
utes. The work cycle is considered to be 35% of this period
of time. Exceeding the work cycle allowed could cause a trip
switch to trip (for further information see the control panel man-
ual), which protects the components inside the welding power
source against dangerous overheating. After several minutes
the overheat cut-off rearms automatically and the welding pow-
er source is ready for use again.
Table 1
Model
DIX PI GO 2006.M / DIX PI GO 2006.M Puls
MIG/MAG TIG MMA
Three-phase input 50/60 Hz
V 400 ± 15%
Mains supply: Z
max
(*) Ω
0,037
Power input (I
2
Max)
kVA 10 8,5 11
Delayed fuse (I eff)
A 16 10 16
Power factor / cosφ
0,74 / 0,99 0,69 / 0,99 0,77 / 0,99
Efficiency degree
η
0,89 0,86 0,9
Voltage without load
V 60
Current range
A 10 ÷ 250
Welding current @ 100% duty cycle (40°C)
A 180
Welding current @ 60% duty cycle (40°C)
A 200
Welding current @ 35% duty cycle (40°C)
A 250
Wires diameter
mm 0,6 - 1,2 - -
Welding wire spool
Diameter / Weight
mm / kg 300 / 15 - -
N° drive rolls
4 - -
Power output of feeder motor
W 55 - -
Rated wire feeding speed
m/min 0,5 ÷ 22 - -
Ø
MMA electrodes
mm - - 1,6 - 4,0
Ø
TIG electrodes
mm - 1,0 - 3,2 -
Shield gas
•
Carbon dioxide
•
Pure Argon
•
Argon - Carbon dioxide
- Oxygen
•
Argon and Carbon
dioxide blends
- -
Standards
IEC 60974-1 - IEC 60974-5 - IEC 60974-10 -
Protection class
IP 23 S
Insulation class
H
Dimensions
mm 650 - 388 - 300
Weight
kg 21
(*) Mains supply Z
max
: maximum impedance value allowed for the grid according to the EN/IEC 61000-3-11 standard.
WARNING: This welding power source does not comply with EN/IEC 61000-3-12. If it is connected to a public low voltage system, it is the re-
sponsibility of the installer or user of the welding power source to ensure, by consultation with the distribution network operator if necessary, that
the welding power source may be connected.