DINSE DIX PI GO 2006.M, Руководство по эксплуатации

Страница: 24 / 36

24
MIG-MAG synergic / MIG pulse
/ double pulsed MIG
Start the welder by pressing the switch, located on the back pan-
el, at the position
I .
1 - WELDING PROCESS SELECTION
Select the MIG welding PROCESS this way:
1) Push the SELECT WELDING PROCESS (T2) key, even a
number of times if necessary, until the corresponding LED
switches on.
T2
2) Push the SELECT PROGRAM key (T5). The corresponding
LED switches on.
T5
3A) To access the MIG-MAG synergic welding process: rotate the
ENCODER knob - A (E1) until obtaining on the PARAMETER
DISPLAY screen - A (D1) and the writing
MiG .
E1
3B) To access the MIG pulse welding process: rotate the ENCOD-
ER knob - A (E1) until obtaining on the PARAMETER DISPLAY
screen - A (D1) and the writing
PLS .
D1
E1
3C) To access the double pulsed MIG welding process: rotate the
ENCODER knob - A (E1) until obtaining on the PARAMETER
DISPLAY screen - A (D1) and the writing
dPL .
D1
E1
2 - SELECTION OF WELDING PROGRAMME
PROGRAM TABLE PRG
MIG-MAG-PULSE PROCESS
PROGRAM
NUMBER
MATERIAL
WIRE Ø
(mm)
GAS
DISPLAYS
TYPE CLASS MiG PLS
dPL
000 Fe G3 Si-1 0.6 CO
2
●
001 Fe G3 Si-1 0.8 CO
2
●
002 Fe G3 Si-1 1.0 CO
2
●
010 Fe G3 Si-1 0.6 Ar/16-20%CO
2
●
011 Fe G3 Si-1 0.8 Ar/16-20%CO
2
● ●
012 Fe G3 Si-1 1.0 Ar/16-20%CO
2
● ●
015 Fe G3 Si-1 0,9 Ar/16-20%CO
2
● ●
051 Fe G3 Si-1 0.8 Ar/21-25%CO
2
●
055 Fe G3 Si-1 0.9 Ar/21-25%CO
2
●
195 Fe-rutil flux-cored E71T-GS 0.9 - ●
231 CrNi 308 G 19 9 LSI 0.8 Ar/2-3%CO
2
● ●
232 CrNi 308 G 19 9 LSI 1.0 Ar/2-3%CO
2
● ●
402 Al 99.9 S Al 1050 1.0 Ar ● ●
403 Al 99.9 S Al 1050 1.2 Ar ● ●
412 Al Mg 5 S Al 5356 1.0 Ar ● ●
413 Al Mg 5 S Al 5356 1.2 Ar ● ●
422 Al Si 5 S Al 4043A 1.0 Ar ● ●
423 Al Si 5 S Al 4043A 1.2 Ar ● ●
472 Al Si12 S Al 4047A 1.0 Ar ● ●
511 Cu Si 3 S CuSi3 0.8 Ar ● ●
512 Cu Si 3 S CuSi3 1.0 Ar ● ●
515 Cu Si 3 S CuSi3 0.9 Ar ● ●
911 Fe BD140 0.8 Ar/16-20%CO
2
● ●
951 Fe BD140 0.8 Ar/21-25%CO
2
●
PLS / dPL= Pulse version only
WARNING: This table is merely an example, the welding programs
can be updated and extended. See the table on the welding ma-
chine for the correct list of the programs available.
Select the welding PROGRAMME rotating ENCODER knob - V
(E2) until obtaining on the PARAMETER DISPLAY screen - V (D2)
the desired number.
D2
E2