Digitrax Super Empier Builder Скачать руководство пользователя страница 76 | Manualshive

Страница: 76 / 126

background image

trolled by the 2 digit or 4 digit address. To switch to the 2 digit
address, program a value of 006/x06 into CV29.

2. Select the DCC loco’s 2 digit address on either the L or R Throttle. Be

sure that the address you want to program is the active throttle, the
one with the blinking smoke when you enter programming mode.

3. Enter Program Mode by pressing the PROG Key

to enter pro-

gramming mode. The display will show the last CV and CV Value
you programmed.

4. Select operations mode programming mode by pressing the PROG

Key

until the “Po” appears in the Mode Indicator area of the

LCD. If you are using an infrared or radio throttle, the display will
automatically show Po. The DT400 display will show the address
that was selected on the active throttle in the right side of the bottom
line of the display. This is the address that you are preparing to pro-
gram.

5. Use the L Throttle knob to dial up Ad2 on the left side of the display.

Click the R Throttle knob once to change to Ad4 on the left side of
the display. Use the throttle knobs or numeric keypad to enter the 4
digit address you want to program.

5. Press the ENTER Key

to program the 4 digit address.

6. The display will prompt you with “Ad4on?=y”. Press the Y+ key to

set up the decoder for 4 digit addressing. The display will return to
the programming display with “Ad4=####. Since you have changed
the decoder’s address, you will need to exit ops mode programming
and begin programming again with the new decoder address.

7. When programming is finished, press the EXIT Key

to quit pro-

gramming mode and return to normal operations.

8. With ops mode programming, the command station does not turn off

track power. If you are using a DB150, you do not need to turn track
power back on after programming with ops mode like you do with
service mode programming.

15.5 Busy or Fail Message

If you get a “Busy” message in response to any programming task, the

system is temporarily busy and you will have to try the task again
until you get a “Good” response.

If you get a “Fail” message in response to any programming task, check

to be sure that there is a loco on the programming track and that the
programming track is powered.

E X I T

E N T E R

P R O G

P R O G

75

«
...
74
75
76
77
78
...
»

Содержание Super Empier Builder































































































































Отзывы:

Нет отзывов

Похожие инструкции для Super Empier Builder

Бренд: Quectel Страницы: 23

Бренд: Quectel Страницы: 79

Бренд: Barco Страницы: 6

Бренд: Barco Страницы: 4

Бренд: J3C Страницы: 2

Бренд: Harsco Industrial Страницы: 57

Бренд: Harmar Mobility Страницы: 53

Бренд: IBM Страницы: 276

Бренд: IBM Страницы: 32

Бренд: IBM Страницы: 157

SMARTSTART 6000

Бренд: Zener Страницы: 36

Бренд: Zapi Страницы: 5

UTAdvanced UT35A

Бренд: YOKOGAWA Страницы: 18

1020 CAN-RS232-RS422 MFL

Бренд: PENKO Страницы: 29

Бренд: ShoreStation Страницы: 19

Бренд: EOS Страницы: 7

Бренд: Dudley Страницы: 8

PLATINUM PS-9003

Бренд: HydroQuip Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды