digico D5T, Руководство по эксплуатации

Страница: 102 / 166

Chapter 5
5-12
5) The Current Cue Type
As explained at the start of this chapter, there are 3 different cue types - Normal, Master and Relative .
The updating of cues may differ according to which type is current at the time.
This rule only applies to faders as other controllers will all be updated irrespective of the type of the current cue assuming that the control
in question meets the other criteria.
6) LiveUpdateFadersOption INI file setting
The console has a default INI file setting of LiveUpdateFadersOption=0. If the setting is changed to LiveUpdateFadersOption=1 then
the behaviour of faders in Live Update mode is changed.
NOTE: When a Master Cue is recalled with the LiveUpdateFadersOption=1 setting, the Master's fader positions are copied to all normal
cues.
A summary of the fader functionsfor this and the previous Current Cue Type rule is as follows:
When the current cue is a normal cue
Faders always update other normal cues but not master or relative cues.
When the current cue is a master cue
LiveUpdateFadersOption = 0:
faders only update the current cue and only if Option is pressed
Any changes that are made to the faders in the master cue are temporarily copied through to its relatives so that a consistent fader mix
can be maintained as you pass through the group. As soon as the next master or normal cue is fired the faders will revert to their previ-
ously stored levels
LiveUpdateFadersOption = 1: faders always update other normal cues, and the current cue if Option is pressed
When the current cue is a relative cue
LiveUpdateFadersOption = 0:
if Option is pressed, either the current cue or the current cue’s master is updated, depending on the
Update Group button.
Any changes that are made to the faders in the relative cue are temporarily copied through to the following relatives so that a consistent
fader mix can be maintained as you pass through the group. As soon as the next master or normal cue is fired the faders will revert to their
previously stored levels
LiveUpdateFadersOption = 1: faders always update other normal cues, and either the current cue or the current cue’s master is
updated, depending on the Update Group button.
7) Update Group
The Update Group button may determine whether a single cue or all the cues in a Master/Relative Group will be updated.
When Option is pressed and Update Group is ON, changes may be written to the entire cue group.
General Examples
The following examples all assume that Live Update is switched on and the INI file setting is LiveUpdateFadersOption=0:
NOTE: The exceptions to the following examples are Mutes, Channels Delays, Input and Output Routing and Bussing.
For these controls the Option button has the opposite effect. See section 5.2.4 for examples of these.
5.2.2 Fader Examples ....................................................................
With Option OFF
1)
Current Cue is a Normal Cue and a channel fader which has the same name in all cues is adjusted.
Result: All Normal Cues cues are updated with the fader change but Masters and Relatives are not.
2) Current Cue is a Master Cue and a channel fader which has the same name in all cues is adjusted.
Result: No cues are updated but the change in fader level is maintained through the relatives until the next Master or Normal Cue is fired.
3) Current Cue is a Relative Cue and a channel fader which has the same name in all cues is adjusted.
Result: No cues are updated but the change in fader level is maintained through the relatives until the next Master or Normal Cue is fired.
With Option ON
1)
Current Cue is a Normal Cue and a channel fader which has the same name in all cues is adjusted.
Result : Only the Current Cue is updated.
2) Current Cue is a Master Cue and a channel fader which has the same name in all cues is adjusted.
Result : Only the Current Cue is updated (Unless Update Group is also ON) but relatives would be indirectly affected by the update.
The change in fader level is maintained through the relatives until the next Master or Normal Cue is fired.
3) Current Cue is a Relative Cue and a channel fader which has the same name in all cues is adjusted.
Result : Only the Current Cue is updated (Unless Update Group is also ON).
The change in fader level is maintained through the relatives until the next Master or Normal Cue is fired.