Detecto MedVue MV1 Скачать руководство пользователя страница 35

Страница: 35 / 64

8555-M512-O1 Rev E

MedVue MV1 Owner’s

CALIBRATION SETUP, CONT.

Single Calibration Point

LLOAdEd CAL WT

(Load Calibration Weight)

The display will show

LOAdEd CAL WT

(which is a prompt for entry of the calibration weight

value) and placement of this amount of test weight on scale platform.

1. Make certain scale platform is empty and free of debris.

2. When the display is showing

LOAdEd CAL WT

, the current setting for the calibration

weight will be displayed also.

3. If the value displayed is acceptable, place the calibrated test weight on the scale

platform, and then press the

ENTER

key. Proceed to Step 6.

4. Otherwise, determine the exact amount of test weight to be placed on the scale

platform, and then using the numeric keys enter this value. Allowable values are 1
through scale capacity (refer to the capacity label on MV1).

NOTE:

A minimum of 50% of the scale's capacity is required. However, 70% to 100% is

recommended.

5. Verify that the numbers entered are the same as the amount of test weight, and then

press the

ENTER

key.

6. The display will change to show

PLEASE WAIT

and then starting at the left and

proceeding right, a series of dashes will appear on the display, and then starting at the
right and proceeding left, disappear. Next, the display will change to

UNLOAd SCALE

(Unload Scale)

With the display showing

UNLOAd SCALE

1. Remove the weight from the scale platform.
2. Press the

ENTER

key.

3. The display will change to show

PLEASE WAIT

and starting at the left and proceeding

right, a series of dashes will appear on the display, and then starting at the right and
proceeding left, disappear.

4. Next, the display will change to show the

GRAVITY ENAbLE

prompt.

Содержание MedVue MV1

































































Результаты поиска

Содержание MedVue MV1

Отзывы:

Бренды по названию

Популярные бренды

Detecto MedVue MV1, Руководство пользователя

Результаты поиска

Содержание MedVue MV1

Отзывы:

Бренды по названию

Популярные бренды