Desa IRONHAUS IKC42N Series Скачать руководство пользователя | Manualshive

Страница: 30 / 44

background image

www.ironhaus.com or www.desatech.com

121334-01A

30

2. The receiver continuously receives signals

from the hand-held remote to control the
room temperature. If the hand-held remote
is misplaced, obstructed or for any reason
cannot transmit to the receiver, the receiver

will shut off the fireplace. This will occur in 8

or more minutes depending upon location of
remote transmitter and strength of batteries.

Key Pad Lock Feature

This feature allows the user to lock/unlock the
keypad on the hand-held remote in the MANU
or AUTO mode to prevent inadvertent op-
eration (i.e. children operating the hand-held
remote control, etc.). The keypad is locked in
either on or off. Press the POWER and LOCK
buttons together to turn the unit on or off.

OpERATING OpTIONAL

GWMT1 - WALL MOUNTED

THERMOSTAT

WARNING: Do not con-

nect the thermostat to a power

source. Electrical shock and/or

a fire hazard will occur.

Light fireplace as instructed in

Lighting In-

structions

on page 28. Set wall thermostat to

desired temperature.
This thermostat has been electronically cali-
brated at the factory and requires no adjust-
ment or leveling.

oPeRATIoN

Continued

Upon installation, thermostat must be allowed
to stabilize at room temperature for a minimum
of 30 minutes for proper operation.

To turn fireplace off, adjust thermostat to the

lowest setting and turn gas control knob back
to PILOT. Pilot will remain lit.

IMPORTANT:

To turn pilot off, turn gas control

knob on heater to the OFF position.

OpERATING OpTIONAL

BLOWER ACCESSORY

Locate blower controls by opening lower

louver panel on fireplace. Blower controls are

located on right side of switch bracket to the
left just inside louver panel.
The BK manual blower and BKT thermostat-
ically-controlled blower have an ON setting
and an OFF setting. Blower will only run when
switch is in the ON position. In the OFF posi-
tion, blower will not operate.

Note for BKT Only:

If you are using BKT

blower with optional thermostat (wall mounted

or remote control) for fireplace, your fireplace

and blower will not turn on and off at the same
time. Fireplace may run for several minutes
before blower turns on. After heater modulates
to the pilot position, blower will continue to run.

Blower will shut off after firebox temperature

decreases.

Blower helps distribute heated air from fire

-

place. Periodically check louvers of the firebox

and remove any dust, dirt or other obstruc-

tions that will hinder the flow of air.

Thermocouple

Thermopile

1/8"

Pilot Burner

Piezo
Ignitor

Figure 50 - Pilot Assembly

3/8" to 1/2"

INSPeCTING bURNeRS

Check pilot flame pattern and burner flame

patterns often.

pILOT ASSEMBLY

The pilot assembly is factory preset for the proper

flame height. Alterations may have occurred dur

-

ing shipping and handling. Call a qualified service

person to readjust the pilot if necessary.
The height of thermopile must be 3/8" to 1/2"

above pilot flame as shown in Figure 50. The ther

-

mocouple must be at a height of about 1/8" above

pilot flame. Flame from pilot burner must extend

beyond both thermocouple and thermopile.
If you pilot assembly does not meet these
requirements:

• turn fireplace off (see

To Turn Off Gas to

Appliance

, page 28)

• see

Troubleshooting

, page 33

«
...
28
29
30
31
32
...
»

Содержание IRONHAUS IKC42N Series













































Отзывы:

Нет отзывов

Похожие инструкции для IRONHAUS IKC42N Series

Бренд: Napoleon Страницы: 4

Бренд: LA NORDICA Страницы: 80

COLLETTE L-FT629PST-A

Бренд: HAMPTON BAY Страницы: 6

Бренд: HAMPTON BAY Страницы: 48

Бренд: Majestic Страницы: 57

Бренд: Superior Страницы: 12

Бренд: Napoleon Страницы: 14

Бренд: Napoleon Страницы: 120

Бренд: hergom Страницы: 93

Бренд: barbas Страницы: 84

Regency OXYSAFE 2

Бренд: Valor Страницы: 22

DRT4000-C Series

Бренд: Superior Fireplaces Страницы: 80

AVANT HYFP50085-36

Бренд: Backyard Creations Страницы: 12

Бренд: EINHELL Страницы: 84

Бренд: Signature Design by Ashley Страницы: 39

Patio Lights 23170

Бренд: Landmann Страницы: 4

Бренд: HAMPTON BAY Страницы: 32

Бренд: Wamsler Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды