Desa IRONHAUS IKC42N Series Скачать руководство пользователя

Страница: 24 / 44

www.ironhaus.com or www.desatech.com

121334-01A

pRESSURE TESTING FIREpLACE GAS
CONNECTIONS

1. Open equipment shutoff valve (see Figure

34, page 23).

2. Open propane/LP supply tank valve for

propane/LP fireplace or main gas valve

located on or near gas meter for natural

gas fireplace.

3. Make sure control knob of fireplace is in

the OFF position.

4. Check all joints from equipment shutoff

valve to gas valve (see Figure 35 or
Figure 36, page 23). Apply noncorrosive

leak detection fluid to all joints. Bubbles

forming show a leak. Correct all leaks at
once.

5. Light fireplace (see

Operation

, page 27

and 28). Check all other internal joints for
leaks.

6. Turn off fireplace (see

To Turn Off Gas to

Appliance

, page 28).

INSTALLING OpTIONAL WALL

MOUNT SWITCH - GWMS2

1. Connect one terminal of 25 ft. wire for

wall switch to TPTH terminal on valve.
Connect remaining wire terminal to TH
terminal on valve. Make sure that wire ter-
minals are in positions on unit as pictured
in Figure 37. If wires are not connected as
shown switch will not work.

2. Route 25 ft. wire through openings pro-

vided on sides of burner system to a con-
venient location to mount your switch.

3. Connect one bare wire end to each termi-

nal of the GWMS2 wall switch.

4. Install wall switch and cover in the wall.

FIRePLACe INSTALLATIoN

Continued

Figure 37 - Connecting Wall Switch to

Control Valve

To Wall
Switch
Accessory

INSTALLING OpTIONAL WIRELESS
HAND-HELD REMOTE CONTROL

HRC100 AND HRC200 SERIES

NOTICE: Use only alkaline bat

teries (not included).

Installing Remote Receiver

1. Open bottom louver and locate switch

bracket on the right.

2. Unscrew switch bracket. Lean bracket

forward so you are able to access back
of remote receiver.

3. Locate battery clip mounted on back of

receiver. Slide a 9-volt alkaline battery (not
included) through clip (see Figure 38).

4. Attach terminal wires to battery.
5. Connect wires from receiver to TH and

TPTH to control valve (see Figure 39).

6. Replace switch bracket.

Figure 38 - Attaching Alkaline Battery to

Receiver

Figure 39 - Control Valve Terminals

To Optional
Remote
Accessory

9-Volt
Alkaline
Battery

Receiver

Terminal
Wires

Battery Clip

To Wall
Thermostat

Содержание IRONHAUS IKC42N Series













































Результаты поиска

Содержание IRONHAUS IKC42N Series

Отзывы:

Похожие инструкции для IRONHAUS IKC42N Series

Бренды по названию

Популярные бренды

Desa IRONHAUS IKC42N Series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание IRONHAUS IKC42N Series

Отзывы:

Похожие инструкции для IRONHAUS IKC42N Series

Бренды по названию

Популярные бренды