Desa IRONHAUS IKC42N Series Скачать руководство пользователя | Manualshive

Страница: 42 / 44

background image

www.ironhaus.com or www.desatech.com

121334-01A

42

MANUAL BLOWER KIT - BK

Manual variable control blower accessory
provides better heat distribution. Complete in-
stallation and operation instructions included
in this manual.

ACCeSSoRIeS

THERMOSTATICALLY-

CONTROLLED BLOWER KIT - BKT

Provides better heat distribution. Blower turns
off and on automatically, as needed. Com-
plete installation and operation instructions
included in this manual.

NOTICE: All accessories may

not be available for all fireplace

models.

Purchase these accessories from your local
dealer. If they can not supply these accessories
call DESA Heating, LLC at 1-866-672-6040 for
information. You can also write to the address
listed on the back page of this manual.

BRICK LINER KIT

BL42DA

- Textured Refractory

BL42DSA

- Standard Refractory

BL42DHA

- Textured Refractory Herringbone

BL42DHSA

- Standard Refractory Her-

ringbone
This brick liner adds a touch of style to your

direct-vent fireplace. Complete installation

instructions included in this manual.

FLExIBLE GAS LINE CONNECTOR - CIK

For all models.

pROpANE/NATURAL GAS

CONVERSION KIT

IMPORTANT:

NOT to be used for High Alti-

tude (-HA) Models.

PCDM-42KC

- Propane/LP Gas Conver-

sion Kit

FACE/LOUVER FILIGREE PANEL KIT

FPD42

- Black

FPD42B

- Brushed Brass

FPD42P

- Platinum

FPD42PB

- Polished Brass

ROLLED LOUVER TRIM KIT

LT42B

- Brushed Brass

LT42P

- Platinum

LT42PB

- Polished Brass

DEFLECTION HOODS

HD42

- Black (2" Brow)

PERIMETER TRIM KIT

PT42

- Black

PT42B

-Brushed Brass

PT42P

- Platinum

PT42PB

- Polished Brass

WALL MOUNTED THERMOSTAT

CONTROL KIT - GWMT1

Allows easy wall access for thermostatic

operation of your fireplace.

WALL MOUNTED ON/OFF SWITCH

GWMS2

Allows burner system to be turned on and off
with a wall switch..

RECEIVER AND HAND-HELD

THERMOSTAT REMOTE CONTROL

KIT - HRC200 SERIES

Allows the fireplace to be operated in a manually

or thermostatically-controlled mode. You can ad-

just your heat settings and turn the fireplace on or

off without leaving the comfort of your easy chair.
A wall-mounted docking station is included.

RECEIVER AND HAND-HELD ON/
OFF REMOTE CONTROL KIT
HRC100 SERIES

Allows the fireplace to be turned on and off

conveniently. A wall-mounted docking station
is included.

«
...
40
41
42
43
44
»

Содержание IRONHAUS IKC42N Series













































Отзывы:

Нет отзывов

Похожие инструкции для IRONHAUS IKC42N Series

Бренд: Ravelli Страницы: 7

Бренд: Archgard Страницы: 64

Бренд: Desa Страницы: 36

Бренд: Napoleon Страницы: 2

BRONTE TOP OUTLET RU

Бренд: Firenzo Страницы: 12

Бренд: Malm Fireplaces Страницы: 9

Бренд: Hargrove Страницы: 7

Brentwood Gas Insert

Бренд: Pacific energy Страницы: 24

Бренд: Landmann Страницы: 8

Бренд: FMI Страницы: 40

Бренд: Superior Fireplaces Страницы: 32

Бренд: Amantii Страницы: 20

Бренд: Dimplex Страницы: 22

Ascent BHD4PFCNA

Бренд: Napoleon Страницы: 140

Бренд: KEKAI Страницы: 98

C 350 Winterport

Бренд: Jøtul Страницы: 2

Бренд: GlammFire Страницы: 12

Бренд: Jøtul Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды