Desa IRONHAUS IKC42N Series Скачать руководство пользователя | Manualshive

Страница: 25 / 44

background image

www.ironhaus.com or www.desatech.com

121334-01A

25

Installing 9-Volt Alkaline Battery in Hand-

Held Remote Control Unit

1. Remove battery cover on back of remote

control unit.

2. Attach terminal wires to a 9-volt alkaline

battery (not included). Place battery into
battery housing.

3. Replace battery cover onto remote control

unit.

FIRePLACe INSTALLATIoN

Continued

Figure 40 - Installing Battery in Hand-

Held Remote Control Unit

9-Volt Battery

Battery
Housing

Battery Cover

Terminal
Wires

Remote Control Unit

REMOVING/REPLACING GLASS

DOORS

CAUTION: Do not operate

this fireplace with a broken glass

door panel or without the glass

door panel securely in place.

For replacement part informa

-

tion see

Replacement Parts

,

page 37.

CAUTION: Wear gloves and

safety glasses while handling

or removing broken glass. Do

not remove if glass is hot. Keep

children and pets away from

glass.

WARNING: If fireplace has

been running, turn off and un

-

plug fireplace. Let cool before

removing inner glass door or

louvers.

Removing Louver Panels

Remove  top  and  bottom  louver  panels  by
simultaneously  pulling  both  top  end  spring
latches  towards  center  of  appliance  until
they  are  disengaged  from  locating  holes
(see  Figure  42).  Repeat  for  bottom  spring
latches  and  pull  louvers  outward.  To  install
or  replace  items  removed,  simply  reverse
procedures above.

Figure 42 - Removing Louver Panel

Louver
Panel

Spring
Latch

Figure 41 - Installing Glass Doors

Outer Door Installation

It is important that you remove doors prior

to installing your fireplace. To remove doors,

pull up and out to disengage pins. Set doors

aside until installation of fireplace is complete.

Reinstall doors by seating pin on door into slot
on enclosure frame (see Figure 41).

Pin

Door

Enclosure
Frame

Slot for
Pin

«
...
23
24
25
26
27
...
»

Содержание IRONHAUS IKC42N Series













































Отзывы:

Нет отзывов

Похожие инструкции для IRONHAUS IKC42N Series

Бренд: HAMPTON BAY Страницы: 10

Бренд: GBT Страницы: 18

PALERMO L FTA90546

Бренд: MWH Страницы: 54

Бренд: decorflame Страницы: 21

Бренд: Pacific energy Страницы: 24

Бренд: Comfort Glow Страницы: 20

Бренд: Heat & Glo LifeStyle Страницы: 26

Marquis MCVP42LP

Бренд: Kingsman Fireplaces Страницы: 75

Prescott White Mantel

Бренд: Early Settler Страницы: 4

Бренд: Twin-Star International Страницы: 26

Бренд: Yosemite Страницы: 15

Royale ETR Freestanding

Бренд: Rinnai Страницы: 16

Бренд: Coleman Страницы: 2

Бренд: Coleman Страницы: 16

Бренд: Country Hearth Страницы: 20

Бренд: Capital Страницы: 28

Бренд: Canvas Страницы: 100

Oakville Series

Бренд: Napoleon Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды