Desa IRONHAUS IKC42N Series Скачать руководство пользователя | Manualshive

Страница: 26 / 44

background image

www.ironhaus.com or www.desatech.com

121334-01A

26

Open louvers, unlock door latches and open
glass door. See

Removing Inner Glass Door

,

step 1 column 1.
1. Pull ember material apart into pieces no

larger than a dime. Place these pieces
loosely and sparingly directly onto exposed
front section of burner (see Figure 44). This
will create the glowing ember appearance

as flame touches ember material. Do not

block air slots by using too much ember
material in one area. Do not block pilot
ports with embers. It is not necessary to
use all of the ember material provided.

2. Pour lava rock onto plenum but not onto

flat burner. It is not necessary to use all

of the lava rock provided.

NOTICE: Do not put lava rock on

burner or under burner. Placing

lava rock on burner will cause

performance problems.

3. Close glass door, lock door latchesand

close louvers (see

Removing Inner Glass

Door

, steps 4 and 5).

WARNING: The glass door

must be securely in place before

running this fireplace. Do not run

this fireplace if glass is missing

or broken.

FIRePLACe INSTALLATIoN

Continued

Figure 44 - Placing Ember Material on

Burner

Ember Material

Plenum

Andiron

Removing Inner Glass Door

If replacement of glass is necessary, entire
assembly, glass and frame, must be replaced.
If glass is broken, wear gloves and tape re-
maining fragments onto frame.
1. Lift up on latches to unlock. There are two

on top of firebox and two below firebox that

hold glass door in place (see Figure 43).

2. While holding glass door to prevent it from

falling and causing injury, remove five

screws from hinge located on left side of
door frame assembly (see Figure 43).

3. Remount new frame at hinge with five

new screws before closing door. This will
ensure seating of gasket.

4. Close glass door frame. Lock latches by

placing bar under tab on door and pushing
down and back on latch (see Figure 43,
page 25).

5. Replace louvers by reversing procedure

under

Removing Louver Panels,

page 25.

Lock

Unlock

Glass Frame
Assembly

Screw

Figure 43 - Removing/Replacing Glass

Door

Hinge

Latch

Cleaning Glass Door

See

Cleaning and Maintenance

on page 31.

INSTALLING LAVA ROCK AND

GLOWING EMBERS

It is very important to keep logs exactly as
installed. Do not modify logs. Only use log

set designed for this fireplace.

WARNING: Logs are unitized

and not attached to the burner. Do

not handle log assembly by top logs.

Always pick up by the bottom.

«
...
24
25
26
27
28
...
»

Содержание IRONHAUS IKC42N Series













































Отзывы:

Нет отзывов

Похожие инструкции для IRONHAUS IKC42N Series

Бренд: Valor Страницы: 6

Бренд: FMI Страницы: 32

Бренд: Martin Страницы: 36

Бренд: Spartherm Страницы: 28

Heatilator Icon Series

Бренд: Heatilator Страницы: 2

Бренд: Valor Страницы: 3

Бренд: Valor Страницы: 22

Бренд: Vexar Страницы: 36

astria Mission Mission42TMN

Бренд: IHP Страницы: 32

Бренд: Desa Страницы: 4

Бренд: Renaissance Fireplaces Страницы: 2

CITY LIGHTS Montcello

Бренд: Landmann Страницы: 2

Zermatt 10033051

Бренд: Klarstein Страницы: 44

Бренд: BECAFIRE Страницы: 67

Бренд: Twin-Star International Страницы: 44

Prescott White Mantel

Бренд: Early Settler Страницы: 4

Бренд: ADURO Страницы: 14

Бренд: Napoleon Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды