DentalEZ Core Скачать руководство пользователя страница 8

Страница: 8 / 57

www.DentalEZ.com

866-DTE-INFO

DentalEZ

Equipment

PN: 2717-267C

Section I Introduction

Explanation of Symbols & Signs

Classi

cations

For the purposes of this user manual, the UL

approval is for the unit (head/arm assembly) and

power supply. All other regulatory markings are

provided in their respective manuals.

•

Type of Protection Against Electric Shock:

Class 1 Equipment.

•

Degree of Protection Against Electric Shock:

Type B Applied Parts. The handpiece is

considered an applied part.

•

Degree of Protection Against Ingress of Water:

Ordinary

•

Flammable Gases: Equipment not suitable for

use in the presence of a

ammable anesthetic

mixture with air, oxygen or nitrous oxide.

•

Not intended for use in an oxygen rich

environment.

•

Mode of Operation: Continuous

Medical-General Medical Equipment

Certi

ed as to electrical shock,

and mechanical hazards only in

accordance with:

ANSI/AAMI ES60601-1:2005

CAN/CSA C22.2 NO. 60601-1-08

IEC 80601-2-60:2012

53HN

E355890

The authorized European representative is:

Dental Hygienics & Decontamination (DHD)

41 Blackwell Drive, Braintree Business Park

Braintree Essex, CM7 2PU, UK

Phone: +44 01787 877877 (ext. 200)

= Caution

= Warning

= Biohazard

= Warning - Dangerous Voltage

= General Mandatory Action

= Refer to Manual (Follow Instructions)

= Alternating Current

= Direct Current

= Protective Earth (Ground)

= Type B Applied Part

= European Certi

cation

= Serial Number

= Manufacture Date

= Manufacturer

= Electromagnetic Radiation

= Do Not Trash

= Box Must Remain Upright

= Do Not Place Box on Unlevel Surface

= Do Not Stack Box

= Box Contents Safe Temperature Range

= Box Contents Safe Humidity Range

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 8 / 57

Результаты поиска

Содержание Core

Отзывы: