DentalEZ Core Скачать руководство пользователя страница 4

Страница: 4 / 57

www.DentalEZ.com

866-DTE-INFO

DentalEZ

Equipment

PN: 2717-267C

This manual contains installation, operation and

care instructions, and user service information for

the DentalEZ® CORE™ Magellan Dental Delivery

Unit.

The CORE Magellan unit is intended to be used

by trained professional dental care personnel

only as an interface device to connect the dental

operatory hand instruments to the appropriate

supply utility such as air, water, vacuum, drain and

electrical. It functions as a system management

device that provides a method of operating the

hand instruments from a single control input

device.

The CORE Magellan unit is manufactured to be

used with a dental chair that supports a patient

in a reclined seated position. Operators will be

positioned around the patient’s head as required

for optimum access for the speci

c procedure

being performed. The delivery unit positions the

handpieces for the optimum presentation to the

operator.

The CORE Magellan unit is designed to provide

trouble-free service when installed, operated and

cared for according to the procedures set forth in

this manual.

To ensure proper installation, carefully

read all of the instructions contained in

this manual, paying close attention to all

warnings, cautions and notes.

Before starting installation procedures, review

the illustration to become familiar with the

components of the CORE Magellan unit

(Figure 1)

After the CORE Magellan unit is installed, review

the features, operation procedures, and care

guidelines with the doctor’s sta

Leave this manual in the doctor’s o

ice.

Section I Introduction

Product Overview

• Installation by an authorized

DentalEZ dealer service technician is

recommended.

• For any questions about an order, please

contact a DentalEZ Equipment customer

service representative at 866-DTE-INFO.

NOTICE

Figure 1. Main components of the CORE Magellan unit

Adjustable

Arm

Light Post

(Optional)

Magellan

Unit Post

Delivery

Head

Clean

Water

System

Magellan

Unit

Support

Rear Assistant’s

Arm & Mount

(Optional

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 4 / 57

Результаты поиска

Содержание Core

Отзывы: