DentalEZ Core Скачать руководство пользователя страница 26

Страница: 26 / 57

www.DentalEZ.com

866-DTE-INFO

DentalEZ

Equipment

PN: 2717-267C

Section III Installation

Assistant’s Arm

(Opt)

(Continued)

Assistant’s Instrumentation

5. From the underside of the bracket, install the

nut on the shoulder bolt and

tighten securely

with 9/16" socket.

6. Replace the cap in the link.

7. Pass the tubing and wires from the assistant’s

arm through the strain relief bushing in the

cantilever cover

8. Pass the tubing and wires through the wire

bracket.

9. Connect the 5/8" ID vacuum hose of the rear

assistant’s arm to the 5/8" ID vacuum hose of

the chair by sliding it over the connector of the

chair's ducting hose.

10. Cut o

excess vacuum tubing, if necessary.

11. Refer to tubing diagram (PN: 2662-304) for

air/water connections.

12. For touchpad control equipped, route harness

through chair, connect terminal to main

control board, and coil excess harness.

Saliva Ejector (SE)

1. Connect the SE valve to the 5/16" OD SE tubing

(Figure 23)

2. Hang the SE valve in the instrument holder.

3. Connect the SE tubing to the

open

1/4" port

under the solids collector in the assistant’s

arm.

High Volume Evacuator (SE)

1. Connect the HVE valve to the 5/8" OD tubing

(Figure 24)

2. Hang the HVE valve in the instrument holder.

3. Connect the tubing to an

open

1/2" port under

the solids collector in the assistant’s arm.

4. If an optional second high volume evacuator

valve is used, remove plug.

Air/Water Syringe

NOTE:

The syringe for the delivery head is factory

installed.

Figure 23. Connect SE tubing and SE valve

SE Valve

5/16" OD SE Tubing

Figure 24. Connect HVE valve and OD tubing

HVE Valve

5/8" OD Tubing

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 26 / 57

Результаты поиска

Содержание Core

Отзывы: