DentalEZ Core Скачать руководство пользователя страница 13

Страница: 13 / 57

www.DentalEZ.com

866-DTE-INFO

CORE

Magellan Unit

PN: 2717-267C

Section II Preinstallation

Unit Placement

• DO

NOT

position equipment any place

where it would interfere with unplugging

the power cord from the receptacle.

• The plug cannot be located in a position

that requires tools to access.

WARNING

Utility Service Center (USC)

Parts Included

•

Utility Service Center (USC)

•

USC Cover

•

USC Template

•

Bag of Supplies

• Set the USC cover aside until all

installation and testing of the delivery

system is complete.

• DO NOT DISCARD

the USC template after

use. Neatly refold it and place in it the

back of this user manual.

NOTICE

Tools Required

•

Drill

USC Site Preparation

1. Remove and unfold the full-size USC template

found in the USC carton.

2. Position the USC template according to the

exact layout indicated, making certain correct

distance from base to chair is maintained.

3. Using the USC template, drill four corner

mounting holes for the USC base. DO NOT

secure the base to the

oor at this time.

NOTE:

For wood or metal

oors, drill 5/32" holes.

For concrete

oors, drill 1/4" holes and install

plastic anchors.

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 13 / 57

Результаты поиска

Содержание Core

Отзывы: