DentalEZ Core Скачать руководство пользователя страница 17

Страница: 17 / 57

www.DentalEZ.com

866-DTE-INFO

CORE

Magellan Unit

PN: 2717-267C

Section III Installation

Magellan Unit Support

(Continued)

NuSimplicity Chair

1. Raise the base and back to full

position.

Disconnect

the chair from the power supply.

3. Take o

the chair’s seat by removing the

1/4-20 thumb screw from underneath the seat.

Push the seat toward the back of the chair to

clear the substrate from the slide bosses, then

set the seat aside with all related hardware

(Figure 11)

NOTE:

If installing the CORE delivery unit on a

DentalEZ chair that is not pre-tubed, continue with

the following instructions. If installing on a pre-

tubed chair,

skip steps 4 through 10

Figure 11. Remove the chair seat

Substrate

1/4-20 Thumb

Screw

7. Place a level on the Magellan unit support,

parallel with and perpendicular to the chair

center line, then check the level of the unit

support.

NOTE:

If leveling is necessary, adjust the 3/16" set

screws until the unit support is level.

8. Tighten M16 bolt (55 foot-pounds).

NOTE:

If necessary, repeat steps 5, 6 and 7 after

unit and light are added to re-level.

4. Select the following items from the Magellan

unit support hardware package:

•

Three 1/2"

1½" Bolts

•

Three 1/2" Lock Washers

•

Four 1/2" Flat Washers

•

Four 1/2" Shims

•

Two 3/8"

1/2" Set Screws

5. Determine if the two outside 1/2" threaded

hole mounting pads and the Magellan unit

support are level. If the mounting pads or unit

support are not level, select the necessary

amount of 1/2" shims needed to provide a level

condition across the two pads.

6. Position the Magellan unit support so that

the three 1/2" through holes align with the

corresponding threaded holes of the chair

mount casting.

7. Install the two outside 1/2" bolts and lock

washers and the number of 1/2" shims

determined in step 5 through the Magellan

unit support and thread into the chair mount

casting.

8. Tighten both outside 1/2" bolts to allow a 3/16"

clearance at the middle 1/2" bolt location.

9. Install the middle 3/8" set screws in the

bottom of the Magellan unit support.

10. Install the middle 1/2" lock washer and 1/2"

bolt,

but

do not

fully tighten

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 17 / 57

Результаты поиска

Содержание Core

Отзывы: