DentalEZ Core Скачать руководство пользователя страница 10

Страница: 10 / 57

www.DentalEZ.com

866-DTE-INFO

DentalEZ

Equipment

PN: 2717-267C

Section I Introduction

Safety Precautions

(Continued)

• Medical electrical equipment needs

special precautions regarding

electromagnetic (EMC) compatibility

and needs to be installed according to

EMC information. (See EMC Information

provided in this manual.)

• In accordance with Part 15 of FCC rules,

this equipment was tested and complies

with Class A digital device limits. These

limits are designed to give equipment

reasonable protection against

detrimental interference when operated

in a commercial environment.

• Mobile radio frequency (RF)

communications equipment can a

ect

medical electrical equipment.

• Accessory equipment not complying with

the Medical Device Safety standard IEC

60601-1 may contribute to a reduced level

of safety of the CORE Delivery Unit. It is

necessary for all accessory equipment

and attachments to comply with IEC

80601-2-60 Medical Electrical Equipment.

NOTICE

This equipment has been tested and found

to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide

reasonable protection against harmful

interference in a residential installation.

This equipment generates, uses and

can radiate radio frequency energy, and

if not installed and used in accordance

with the instructions, may cause harmful

interference to radio communications;

however, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception (which can be determined by

turning the equipment o

and on) the

user is encouraged to try to correct the

interference by one or more of the following

measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment to an outlet on

a circuit di

erent from that to which the

receiver is connected.

• Consult the dealer or an experienced

radio/TV technician for help.

NOTICE

Содержание Core


























































Результаты поиска

Содержание Core

Отзывы:

DentalEZ Core, Руководство пользователя, Страница: 10 / 57

Результаты поиска

Содержание Core

Отзывы: