Delta Hybrid E5 Скачать руководство пользователя страница 48

Страница: 48 / 60

- The settings in Install Settings page can only be adjusted by qualified installers or

engineers. Changing these settings may result in damage to the inverter and other

equipment.

CAUTION !

5.3.8 Install Settings

Install Settings page is for installer only.

To enter this page, installer has to key in installer password.

The page includes following functions :

Inverter ID is used to recognized the inverter when you communicating with

it via RS-485.

• Inverter ID

Inverter will measure the impedance between PV array and PE before

connecting to grid. To avoid risk of electrical shock, it’s not recommending to

disable this function.

• Insulation

Each country has its own electricity regulations. The hybrid inverter can meets

more than one electricity regulations. Installer must select the country correctly.

• Country

Installer can choose the trigger condition of dry contact. The explanations of

these conditions are shown in following table.

• Dry Contact

This option is used to clear the battery power fault message. Before clearing

the fault message, please make sure the battery has been repaired.

• Clear BT PF

Setting

Dry Contact Trigger Timing

Disable

No action.

On Grid

Inverter is connecting to grid.

Insulation

Insulation test fail.

Alarm

Any error or fault occurs.

Any fault occurs.

Table 5-2 : Dry contact trigger condition

Error

Any error occurs.

Fault

This function is currently used in Germany only. Installer in Germany should

set the PV array capacity and enable this function. The maximum feed-in power

to grid will be limited at a percentage of PV array capacity. Installers can set

the various limit percentage to meet the local electricity regulation.

• Subsidy Function

Turning On the Hybrid Inverter

Содержание Hybrid E5





























































Результаты поиска

Содержание Hybrid E5

Отзывы:

Похожие инструкции для Hybrid E5

Бренды по названию

Популярные бренды

Delta Hybrid E5, Руководство по эксплуатации и установке

Результаты поиска

Содержание Hybrid E5

Отзывы:

Похожие инструкции для Hybrid E5

Бренды по названию

Популярные бренды