Delta Hybrid E5 Скачать руководство пользователя страница 29

Страница: 29 / 60

Communication Module has 1 set of emergency power off function (EPO).

When the VCC and INV OFF pins are short-circuited, inverter will shut down

immediately. The module also provides 6 sets of digital input function (K1~K6).

Please refer to

Table 4-7

for the digital input definition. The suitable electric wire

is 30-16AWG.

In Australia and New Zealand, the Demand Response Modes (DRMs) are

also use digital input function to assert. The definition is different from normal

digital input function; please refer to

Table 4-8

for the DRMs pin definitions.

4.8 Digital Input / DRM & EPO Functions

Short

Inverter’s action

VCC & INV OFF

Emergency power off (EPO)

VCC & K1

0% active power

VCC & K2

Maximum 30% active power

VCC & K3

Maximum 60% active power

VCC & K4

Maximum 100% active power

VCC & K5

Reserved

VCC & K6

Reserved

Table 4-7 :

Definition of digital input & EPO functions

Short

Inverter’s action

VCC & INV OFF

DRM 0 (Disconnect from grid)

VCC & K1

DRM 5 (0% generate power)

VCC & K2

DRM 6 (50% generate power)

VCC & K3

DRM 7 (75% generate power and sink reactive power)

VCC & K4

DRM 8 (100% generate power)

VCC & K5

Reserved

VCC & K6

Reserved

Table 4-8 :

Definition of DRMs for Australia and New Zealand

Communication Module has 1 set of Dry Contact. The trigger condition of this

function can be customized by Installer. When the function is triggered, the output

two ports will be short-circuited. Please refer to section

5.3.8 Install Settings

for

more details about trigger condition assignation.

4.9 Dry Contact Connection

Wiring

Содержание Hybrid E5





























































Результаты поиска

Содержание Hybrid E5

Отзывы:

Похожие инструкции для Hybrid E5

Бренды по названию

Популярные бренды

Delta Hybrid E5, Руководство по эксплуатации и установке

Результаты поиска

Содержание Hybrid E5

Отзывы:

Похожие инструкции для Hybrid E5

Бренды по названию

Популярные бренды