Delta A9000 Скачать руководство пользователя страница 13

Страница: 13 / 123

User Manual

A9000

AC Power Source

│

www.deltaww.com

2. Installation

2.1 Inspection

First, inspect any damage that may have occurred during the shipment after unpacking the

instrument. Save all packing materials in case the instrument has to be returned.

If any damage is found, please ﬁle a claim against the carrier immediately. Do not return the

instrument to the factory without obtaining the prior RMA acceptance from Delta.

2.2 Preparation for the Use

Before start using, the instrument must be connected with an appropriate AC line input.

As the instrument is cooled by fans, it must be installed in an area with suﬃcient space for

air circulation. It should be used in an area where the environment temperature does not

exceed 40

℃

2.3 Requirements of Input Power

2.3.1 Ratings
Input Voltage Range: 190-250 VLL, 3 phases 4 wires

△

(ABT A), or

329-433 VLL, 3 phases 5 wires Y

(ABT B)

Input Frequency: 47-63Hz
Max. Current/Phase: 35 A / phase (ABT A) or 25A/phase (ABT B)

WARNING

*** CAUTION ***

The AC source may be damaged if it is operated at an input voltage that is over

its conﬁgured input range.

2.3.2 Input Connection

The input terminal block is located on the instrument rear panel. The temperature rating of

the power cord must be rated at least for 85

℃

. The input power line must have a current

rating, which is greater than or equal to the maximum current rating of the AC source.

Recommend to put a 40A breaker (ABT A) (30A breaker (ABT B)) at AC input side.

WARNING

*** CAUTION ***

There are two input voltage rating models, one is 380 VLL 3 phases 5 wires (Y

connection) used for (ABT B model), and the other is 220 VLL 3 phases 4 wires

(

connection) used for (ABT A model). Be careful to verify the model you have,

and make sure that the main voltage is suitable for the model! AC source may

not operate properly if one phase input voltage is missing, please recheck the

connection.

Содержание A9000




























































































































Результаты поиска

Содержание A9000

Отзывы:

Похожие инструкции для A9000

Бренды по названию

Популярные бренды

Delta A9000, Руководство пользователя

Результаты поиска

Содержание A9000

Отзывы:

Похожие инструкции для A9000

Бренды по названию

Популярные бренды