Dell PowerVault DR4100 Скачать руководство пользователя страница 40

Страница: 40 / 122

When you format a hard drive, allow enough time for the formatting to be completed. Be aware that high-capacity hard
drives can take a number of hours to format.

Removing A 2.5 Inch Hard-Drive Blank (Back)

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks installed.

Pull the hard-drive blank out until it is free of the hard-drive slot.

Figure 12. Removing and Installing a 2.5 Inch Hard-Drive Blank (Back)

1. hard-drive blank (back)

Installing A 2.5 Inch Hard-Drive Blank (Back)

Insert the hard-drive blank into the hard-drive slot until it clicks into place.

Removing A 3.5 Inch Hard-Drive Blank

CAUTION: To maintain proper system cooling, all empty hard-drive slots must have drive blanks installed.

If installed, remove the front bezel.

Grasp the front of the hard-drive blank, press the release button and slide the blank out until it is free of the hard-

drive slot.

Содержание PowerVault DR4100



























































































































Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды

Dell PowerVault DR4100, Руководство пользователя

Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды