Dell PowerVault DR4100 Скачать руководство пользователя страница 106

Страница: 106 / 122

Error Code

Message Information

Action

Check the operating system, application, hardware, and system event
log for exception events.

ASR0001

Message

The watchdog timer reset the system.

Details

The operating system or an application failed to communicate within
the time-out period. The system was reset.

Action

Check the operating system, application, hardware, and system event
log for exception events.

ASR0002

Message

The watchdog timer powered off the system.

Details

The operating system or an application failed to communicate within
the time-out period. The system was shut down.

Action

Check the operating system, application, hardware, and system event
log for exception events.

ASR0003

Message

The watchdog timer power cycled the system.

Details

The operating system or an application failed to communicate within
the time-out period. The system was power-cycled.

Action

Check the operating system, application, hardware, and system event
log for exception events.

BAT0002

Message

The system board battery has failed.

Details

The system board battery is either missing or bad.

Action

See

Getting Help

BAT0017

Message

The <

name

> battery has failed.

Details

The <

name

> battery is either missing, bad, or unable to charge due to

thermal issues.

Action

Check system fans. If the problem persists, see

Getting Help

CPU0000

Message

CPU <

number

> has an internal error (IERR).

Details

System Event Log and Operating System Logs may indicate that the
exception is external to the processor.

Action

Review System Event Log and Operating System Logs. If the issue
persists, see

Getting Help

CPU0001

Message

CPU <

number

> has a thermal trip (over-temperature) event.

106

Содержание PowerVault DR4100



























































































































Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды

Dell PowerVault DR4100, Руководство пользователя

Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды