Dell PowerVault DR4100 Скачать руководство пользователя страница 11

Страница: 11 / 122

Drive-Status
Indicator Pattern
(RAID Only)

Condition

Steady green

Drive online

Blinks green three
seconds, amber three
seconds, and off six
seconds

Rebuild aborted

Back-Panel Features And Indicators

The following topic describes the back-panel features and indicators of the Dell DR4100 system.

Figure 3. Back-Panel Features And Indicators

Item

Indicator, Button, or

Connector

Icon

Description

System identification button

The identification buttons on the front and back panels
can be used to locate a particular system within a rack.

•

When one of these buttons is pressed, the system

status indicator on the back flashes until one of

the buttons is pressed again.

•

Press to toggle the system ID on and off.

•

If the system stops responding during POST, press

and hold the system ID button for more than five

seconds to enter BIOS progress mode.

•

To reset iDRAC (if not disabled in F2 iDRAC setup)

press and hold the button for more than 15

seconds.

System identification
connector

Connects the optional system status indicator assembly
through the optional cable management arm.

iDRAC7 Enterprise port

Dedicated management port.

NOTE: The port is available for use only if the iDRAC7
Enterprise license is installed on your system.

PCIe expansion card slots
low-profile (3)

Allows you to connect up to three PCI Express expansion
cards.

Serial connector

Allows you to connect a serial device to the system.

Video connector

Allows you to connect a VGA display to the system.

Содержание PowerVault DR4100



























































































































Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды

Dell PowerVault DR4100, Руководство пользователя

Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды