Dell PowerVault DR4100 Скачать руководство пользователя страница 100

Страница: 100 / 122

Memory

Architecture

800 MT/s, 1066 MT/s, 1333 MT/s or 1600 MT/s DDR3
registered Error Correcting Code (ECC) DIMMs

Support for advanced ECC or memory optimized
operation

Memory module sockets

Twenty-four 240-pin

Memory module capacities

8 GB dual ranked RDIMMs

RAM

32 GB with two processors

Drives

Hard drives

Up to twelve 3.5 inch, internal, hot-swappable, Nearline SAS
drives, and two optional 2.5 inch back-accessible SAS,
Nearline SAS hard drives in hard-drive slots 0 through 11
and 12 through 13.

Connectors

Back

NIC

Four 10/100/1000 Mbps or two 10/100/1000 Mbps and two
100 Mbps/1 Gbps/10 Gbps

Serial

9-pin, DTE, 16550-compatible

USB

Two 4-pin, USB 2.0-compliant

Video

15-pin VGA

Front

USB

One 4-pin, USB 2.0-compliant

Video

15-pin VGA

Internal

USB

One 4-pin, USB 2.0-compliant

Internal Dual SD Module

Two optional flash memory card slots with the internal SD
module

NOTE: One card slot is dedicated for redundancy.

Video

Video type

Integrated Matrox G200

Video memory

16 MB shared

Expanded Operating Temperature

NOTE: When operating in the expanded temperature range, system performance may be impacted.

100

Содержание PowerVault DR4100



























































































































Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды

Dell PowerVault DR4100, Руководство пользователя

Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды