Dell PowerVault DR4100 Скачать руководство пользователя страница 12

Страница: 12 / 122

Item

Indicator, Button, or

Connector

Icon

Description

USB connectors (2)

Allows you to connect USB devices to the system. The
ports are USB 2.0-compliant.

Ethernet connectors

Four integrated 10/100/1000 Mbps NIC connectors
or
Four integrated connectors that include:

•

Two 10/100/1000 Mbps NIC connectors

•

Two 100 Mbps/1 Gbps/10 Gbps SFP+/ 10GBASE-T

connectors

PCIe expansion card slots
full height (3)

Allows you to connect up to three full-height PCI Express
expansion cards.

Power supply (PSU1)

750 W

Power supply (PSU2)

750 W

Hard drives (2) (back)

Two hot-swappable 2.5 inch hard drives.

vFlash media card slot

Allows you to insert a vFlash media card.

NOTE: The vFlash media card slot is not active on the
DR4100. Do not use this slot.

NIC Indicator Codes

The following topic describes the NIC indicator codes of the Dell DR4100 system.

Figure 4. NIC Indicator

1. link indicator
2. activity indicator

Indicator

Indicator Code

Link and activity
indicators are off

The NIC is not connected to the network.

Link indicator is
green

The NIC is connected to a valid network at its maximum port speed (1 Gbps or 10 Gbps).

Содержание PowerVault DR4100



























































































































Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды

Dell PowerVault DR4100, Руководство пользователя

Результаты поиска

Содержание PowerVault DR4100

Отзывы:

Похожие инструкции для PowerVault DR4100

Бренды по названию

Популярные бренды