Embedded
xxx
initializing PCI device;
faulty system board.
system (see
Figure A-2
for jumper location). If
the problem persists, see "
Troubleshooting
Expansion Cards
" in "Troubleshooting Your
System."
Plug & Play Configuration Error PCI_
n
Error encountered in
initializing PCI adapter.
Primary backplane is not present
Faulty or improperly
installed SCSI backplane
board.
See "
Getting Help
."
Processor
n
internal error
Faulty microprocessor;
faulty system board.
See "
Troubleshooting a Microprocessor
" in
"Troubleshooting Your System."
Processor bus parity error
Processor in socket 1 not installed!
No microprocessor
installed in primary
microprocessor socket.
Install a microprocessor in the primary
microprocessor socket. Also, ensure that a
VRM for processor 1 is installed (see "
Adding
or Replacing a Microprocessor
" in "Installing
System Options").
SCSI cable not present on connector A
or B of the primary backplane
SCSI cable is loose,
improperly connected, or
faulty.
Check the SCSI cable connection. If problem
persists, add or replace SCSI cable (see
"
Getting Help
").
Shutdown failure
Shutdown test failure.
See "
Troubleshooting System Memory
" in
"Troubleshooting Your System."
System backplane error
Faulty or improperly
installed SCSI backplane
board.
See "
Getting Help
."
System halted! Must power down
Wrong password entered
too many times.
Information only.
Time-of-day clock stopped
Faulty battery.
See "
Troubleshooting the System Battery
" in
"Troubleshooting Your System."
Time-of-day not set - please run SETUP
program
Incorrect Time or Date
settings; faulty system
battery.
Check the Time and Date settings (see "Using
the System Setup Program" in the
User's
Guide
). If the problem persists, replace the
system battery (see "
Replacing the System
Battery
" in "Installing System Options").
Timer chip counter 2 failed
Faulty system board.
See "
Getting Help
."
Unsupported CPU combination
Microprocessor(s) is not
supported by the system.
Install a supported microprocessor combination
(see "
Adding or Replacing a Microprocessor
" in
"Installing System Options").
Unsupported CPU stepping detected
Unsupported DIMM detected in the RAID
DIMM slot!
RAID memory module is
not supported by the
system.
Install a correct version of the RAID memory
module (see "
Activating the Integrated RAID
Controller
" in "Installing Drives").
Unsupported RAID key detected!
RAID hardware key is not
supported by the system.
Install the RAID hardware key for your specific
system (see "
Activating the Integrated RAID
Controller
" in "Installing Drives").
The VRM for the processor in socket
n
is not installed.
Specified microprocessor
VRM is faulty,
unsupported, improperly
installed, or missing.
Ensure that supported VRMs of the same type
are properly installed. If the problem persists,
replace the VRM (see
Figure 6-9
).
Warning: Detected mode change from RAID
to SCSI B of the embedded RAID
subsystem.
Type of controller has
changed since previous
system boot.
Back up information on the hard drives before
changing the type of controller used with the
drives.
Warning: Detected missing RAID hardware
for the embedded RAID subsystem. Data
loss will occur! Press Y to switch mode
to SCSI, press any other key to disable
both channels. Press Y to confirm the
change; press any other key to cancel.
Warning: Firmware is out- of-date,
please update.
Firmware error.
Update the firmware (see "
Getting Help
").
Warning! No microcode update loaded for
processor X
BIOS error.
Update the BIOS firmware (see "
Getting
Help
").
Содержание PowerVault 775N
Страница 3: ...Back to Contents Page ...
Страница 65: ...Back to Contents Page ...
