Dell PowerEdge 7250 Скачать руководство пользователя страница 86

Страница: 86 / 102

Terminal Mode Commands

www

.del

com |

ppo

rt.

ll.

Boot initiator info

(semi-volatile)

Address and Identity information for the party that initiated the

boot. The party that initiates the boot writes this parameter and

the boot info acknowledge parameter prior to issuing the

command that causes the system power up, power cycle, or reset.

This data is written by the remote console application, not the

BMC.
Boot Source
Data 1- Channel Number. Channel that delivers the boot

command (for example, chassis control). BIOS and boot software

(e.g. service partition or operating system loader) can use the

Get

Channel Sessions

to find out information about the party that

initiated the boot
[7:4]—Reserved.
[3:0]—Channel Number.
Data 2:5 - Session ID. Session ID for session that the boot

command will be issued over. This value can be used with the

Get

Channel Sessions

command to find out information about the

party that initiated the boot.
Data 6:9 - Boot Info Timestamp. This timestamp is used to help

software determine whether the boot information is "stale" or not.

A service partition or OS loader may elect to ignore the boot

information if it is older than expected.
The boot initiator should load this field with the timestamp value

from the IPMI

Get SEL Time

command prior to issuing the

command that initiates the boot.

Table C-5. Boot Option Parameters

(continued)

Parameter

Number

Parameter Data (non-volatile unless otherwise noted)

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды