Dell PowerEdge 7250 Скачать руководство пользователя страница 31

Страница: 31 / 102

BMC Management Utility

Installation

To install the BMC Management Utility on the management station, perform the following steps:

Log on with administrator privileges to the system where you want to install the system

management software components.

Exit any open application programs and disable any virus-scanning software.

Insert the

Systems Management and Documentation

CD into your system's CD drive.

The setup program should start automatically. If it does not, click the

Start

button, click

Run

and then type

:autorun.exe

(where

is the drive letter of your CD drive).

Click

Install BMC Management Utilities.

Click

Open

to proceed through the installation process and respond to the prompts, as

required.
The setup program automatically installs all of the management station software for your

hardware configuration.

When the installation is complete, close the installation window.
See the for more information.

See the

Dell OpenManage™ Version 1.8.3 User's Guide

for additional information about installing

the BMC Management Utility on a management station.

Windows Operating Systems

By default, the installation program copies the files to the following directory:

C:\ProgramFiles\ Dell\OpenManage\bmcconsole.

Uninstalling the BMC Management Utility

To uninstall the BMC Management Utility, use the Add/Remove Programs utility in the Control

Panel.

Red Hat Linux Operating Systems

By default, the installation program copies the files to the following locations:

/etc/init.d/solproxy
/etc/solproxy.cfg
/usr/sbin/solproxyd
/usr/bin/solconfig
/usr/bin/ipmish

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды