Dell PowerEdge 7250 Скачать руководство пользователя страница 62

Страница: 62 / 102

BMC Management Utility Error Codes

www

.del

com |

ppo

rt.

ll.

Invalid IP address.

IP resolving error.

Session buffer limit

exceeded.

Length exceeds the limit

of telnet input.

A6h
A8h

Syntax errors.

Command syntax error.

Unable to parse

command.

Unrecognized

command.

Unrecognized

Command.

Time format is incorrect.

The time is not correct.

Conflicting option.

Conflicting option (

-last

and

-max

Invalid

parameter.

Invalid

Parameter.

A7h

Parameter value

errors.

Parameter out of range.

Parameter out of range. 0xC9

Parameter out of range (1-

255)

The value is out of range

(1-255).

Parameter out of range(1-

65535).

The value is out of range

(1-65535).

Invalid data field.

0xCC

Invalid index value.

Index cannot be zero or a

negative number.

First index larger than the

last.

The first index is larger

than the last.

First index larger than total

SEL records.

The first index is larger

than the total SEL

records.

A8h

H/W or F/W

errors.

Unsupported command.

Unsupported Operation. 0xC1

Sensor not present.

Request sensor, data, or

record not present.

0xCB

Sensor command error.

Command illegal for

specified sensor or record

type.

0xCD

Firmware error.

Command response

could not be provided.

0xCE

Table A-1. BMC Management Utility Error Codes

(continued)

Code

Classification

Message

Description

IPMI Error

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды