Dell PowerEdge 7250 Скачать руководство пользователя страница 26

Страница: 26 / 102

Configuring Your Managed System

www

.del

com |

ppo

rt.

ll.

Figure 2-4. Serial Over LAN Configuration Screen

After configuring the SOL information, click

Save

to complete this subtask.

Enable Serial Over LAN

This check box is used to enable or disable the serial over LAN capability.

SOL Privilege Level

This setting is used to select the minimum BMC privilege level that is required to be able to

activate SOL. The choices are User, Operator, and Administrator. For the best performance, User

should be selected.

Number of Retries

This field sets the number of times that the BMC tries to resend a SOL message to a remote

console.
The number of retries must between 0 and 7.

Retry Interval

This field sets the number of milliseconds that the BMC waits between trying to send SOL

messages to a remote client.
The value entered must be between 0 and 2559. The SMU truncates the digit in the ones column

from any input number because the firmware maintains this value in 10 millisecond intervals.

Therefore, any value that is entered between 0 and 9 is displayed as 0.

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды