Dell PowerEdge 7250 Скачать руководство пользователя страница 22

Страница: 22 / 102

Configuring Your Managed System

www

.del

com |

ppo

rt.

ll.

Figure 2-3. LAN Channel Configuration Screen

After completing this screen, click

Next

to move to the next screen to continue this sub-task.

Default LAN Configuration Settings Set by the SMU

The SMU automatically configures some server management firmware settings. These are not

displayed on the screen above, but are listed below. Before these settings are set by the SMU, you

must click through each LAN configuration screen by clicking the Next button until you reach the

Save button on the final LAN configuration screen.

•

Gratuitous ARPs may be enabled:

This setting allows the BMC to generate gratuitous ARPs,

which provide a mechanism for IP devices to locate the hardware addresses of other devices

on the local network. If the system has a valid IP address and the LAN channel is enabled for

messaging (the access mode is not set to Disabled) or alerting, then gratuitous ARPs are

enabled.

•

Authentication enables are enabled:

These bits define what types of authentication are

enabled to authenticate messages sent to the BMC by users of different privilege levels. The

SMU enables authentication of type straight password, MD2, MD5, and none.

•

User-level authentication is disabled:

The SMU disables user-level authentication so that if a

user is attached with a privilege level of User, no authentication is done on messages sent to or

from the BMC. This improves the session performance.

Содержание PowerEdge 7250







































































































Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды

Dell PowerEdge 7250, Руководство пользователя

Результаты поиска

Содержание PowerEdge 7250

Отзывы:

Похожие инструкции для PowerEdge 7250

Бренды по названию

Популярные бренды